Hideaway Deluxe Series Comment entretenir

Parcourez en ligne ou téléchargez le pdf Comment entretenir pour {nom_de_la_catégorie} Hideaway Deluxe Series. Hideaway Deluxe Series 2 pages. Range floor mount
Également pour Hideaway Deluxe Series : Instructions d'installation (2 pages), Instructions d'installation (2 pages)

Imprimer la page

How to care for and maintain

NOTE: Diagrams indicating the different bin components can be found in the downloadable installation

instructions for each bin model. This is located on our website in the INFO / DOWNLOADS section.

IMPORTANT INFORMATION

• Do not over fill your bin as contents could scratch your

friction-fitted lid (Deluxe & Soft Close ranges only).

• Refrain from pushing down on rubbish inside your bucket/s as

this creates extra pressure on the screw fixings inside the cabinet.

How to keep your Hideaway Bin clean

• It is recommended you use warm soapy water to clean your

Hideaway Bin.

• Avoid hard abrasive cleaners.

• When cleaning, try to avoid getting the runners wet, however,

if this happens ensure you dry the runners well and then regrease

with a small amount of petroleum jelly, such as Vaseline, or a clear

silicone grease.

How to care for, remove and replace

runners for cleaning

TO CARE FOR YOUR RUNNERS (all bin models):

• Over time you may need to lubricate your runners for continued

free movement. To do this, lube with a small amount of petroleum

jelly, such as Vaseline, or a clear silicone grease. For Deluxe and

Compact models, the runners can be separated, which makes it

easier to clean and lubricate. See instructions below for separating

runners.

• Your Hideaway Bin has ball bearing runners which gain a

memory over time. This occurs due to the bin usually being opened

partially during everyday use. This can make it difficult to open the

bin fully. To ensure your bucket/s will always come clear of your

bench top, every so often place a firm grip on either side of your

handle/door bracket and slowly, but firmly, pull the unit towards

you. Continue to pull the runners towards you until they reach

their maximum extension. Then close your unit fully again.

TO SEPARATE RUNNERS FOR CLEANING (all Deluxe models and

Compact KC240 &KC235 models):

• Remove the buckets from your unit. Fully extend the runners. To

do this, find the black levers located on the outer side of both the

left and right runner.

Runners engaged - push left lever

down and right lever up

Runner Outer

Black lever

Runner

on runners

Inner

your Hideaway

(Compact, Deluxe, Soft Close Ranges)

Runners disengaged - pull the runner

inner clear of the outer

Runner Outer

Runner Inner

Pull the inner runner out until

it separates from the unit

Bin

• Simultaneously, push the left lever down and the right lever

up and pull inner of the runners towards you until it separates

completely from the unit. Set runner inner with collar, handle/door

bracket attached aside in a safe location.

• Push the outer runners attached to the top mounting panel

back inside the unit.

TO SEPARATE RUNNERS FOR CLEANING

(all other Compact models):

• Remove the buckets from your unit. Fully extend the runners.

• Press the yellow runner release latches on both sides.

• Holding the mounting panel securely, pull the handle or door

bracket to separate the inner components from the mounting

panel.

Runner

Yellow Runner Release Latch

TO CLEAN AND REATTACH RUNNERS

(Deluxe and Compact models only):

• Ensure the outer runners attached to the top mounting panel

are pushed all the way inside the unit. With the outer runners,

ensure the inner slider is pulled all the way towards the front of

the unit.

• Wipe runners with a clean cloth, cotton bud or toothbrush.

Apply a small amount of petroleum jelly, such as Vaseline, or a

clear silicone grease to the runners.

• Line up the inner runners (with collar attached) to the outer

runners that are attached to the top mounting panel (which is

installed in your cupboard).

• Push the inner runners all the way in until the unit closes to

engage the runners. Pull unit open again. The runners should

move with ease indicating correct positioning.

Mounting Panel