HIKOKI C 7SB3 Manuel d'instructions de manutention - Page 9
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions de manutention pour {nom_de_la_catégorie} HIKOKI C 7SB3. HIKOKI C 7SB3 16 pages.
Imprimer la pageADDITIONAL SAFETY WARNINGS
1. Use only blade diameter specifi ed on the machine.
2. Do not use any abrasive wheel.
3. Do not use saw blades which are deformed or cracked.
4. Do not use saw blades made of high speed steel.
5. Do not use saw blades which do not comply with the
characteristics specifi ed in these instructions.
6. Do not stop the saw blades by lateral pressure on the
disc.
7. Always keep the saw blades sharp.
8. Ensure that the lower guard moves smoothly and freely.
9. Never use the circular saw with its lower guard fi xed in
the open position.
10. Ensure that the retraction mechanism of the guard
system operates correctly.
11. Never operate the circular saw with the saw blade turned
upward or to the side.
12. Ensure that the material is free of foreign matters such as
nails.
13. For model C7SB3, the saw blades range should be from
185 mm to 180 mm.
14. Disconnect the plug from the receptacle before carrying
out any adjustment, servicing or maintenance.
15. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
16. Before the tool is plugged in to the receptacle, ensure
that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
17. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
NAME OF PARTS (Fig. 1 – Fig. 15)
Switch trigger
1
Saw cover
2
Lower guard lever
3
M8 bolt
4
Washer (B)
5
Saw blade
6
Lower guard
7
Guide
8
Base
9
Inclined lever
0
Guide fastener wing-
!
bolt
Inclined gauge
@
Brush cap
#
Handle
$
Lock lever
%
Nameplate
^
Lever
&
Cord holder
*
18. Since the saw blade will extend beyond the lower surface
of the lumber, place the lumber on a workbench when
cutting. If a square block is utilized as a workbench,
select level ground to ensure it is properly stabilized. An
unstable workbench will result in hazardous operation.
(Fig. 2)
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
19. Should lever remain loosened, it will create a very
hazardous situation. Always thoroughly clamp it. (Fig. 3)
20. It is very hazardous to allow Inclined lever to remain
loosened. Always thoroughly clamp it. (Fig. 4)
21. Prior to cutting operation, make sure the material you
are going to cut. If the material to be cut is expected to
generate harmful / toxic dusts, make sure the dust bag
or appropriate dust extraction system is connected with
dust outlet tightly.
Wear the dust mask additionally.
○ Before starting to saw, confi rm that the saw blade
has attained full-speed revolution.
○ Should the saw blade stop or make an abnormal
noise while operating, promptly turn OFF the switch.
○ Always take care in preventing the power cord from
coming near to the revolving saw blade.
○ Using the circular saw with the saw blade facing
upwards or sideways is very hazardous. Such
uncommon applications should be avoided.
○ When cutting materials, always wear protective
glasses.
○ When fi nished with a job, pull out the plug from the
receptacle.
22. After having attached the saw blade, reconfi rm that the
lock lever is fi rmly secured in the prescribed position.
23. Do not use the tool with only the blower function.
24. Check that there are no nicks or scratches in the cord.
25. Check the exterior and ensure that there is no damage.
26. Use a saw blade with a displayed rotational speed equal
to or higher than the rotational speed of the tool.
27. Use a saw blade that suits each diff erent cutting material.
Lumber
(
Workbench
)
Lock spring
q
Premarked line
w
Front scale at 45°
e
incline
Front scale when not
r
inclined
Lever (short type)
t
Dust collector
y
M4 Screw
u
9
6 mm Hex. bar wrench
i
Washer (A)
o
Square
p
Hex. socket set screw
a
3 mm Hex. bar wrench
s