IKEA IUD9500VX0 Manuel d'instructions d'installation - Page 5
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} IKEA IUD9500VX0. IKEA IUD9500VX0 40 pages. Undercounter dishwasher plastic giant tubmodels
Également pour IKEA IUD9500VX0 : Instructions pour l'utilisateur (20 pages)
Imprimer la page
•
A hot water line with 20-120
psi (138-862
kPa) water pressure.
•
120°F (49°C) water temperature
at dishwasher.
•
Flexible stainless steel braided fill line V2" [1.27 cm] minimum
plastic tubing is not recommended).
Contact a qualified electrician.
Ensure that the electrical installation is adequate and in
conformance with all national and local codes and ordinances.
You must have:
•
120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical
supply.
•
Copper wire only.
We recommend:
•
A time-delay fuse or circuit breaker.
•
A separate circuit.
If direct wiring dishwasher:
•
Use flexible, armored or nonmetallic sheathed, copper wire
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
•
Use strain relief method provided with house wiring junction
box or install a UL-listed/CSA-certified
clamp connector to the
house wiring junction box. If using conduit, use a
UL-listed/CSA-certified
conduit connector.
If connecting
dishwasher
with a power supply cord:
•
Use Power Supply Cord Kit (Part Number 4317824) marked
for use with dishwashers. Kit contents include:
•
Voltex, Inc., UL listed 16 gauge 3 wire power supply cord
with 3 prong grounded plug.
•
Neer C-500 7/8"strain relief.
•
3 wire connectors.
•
Part Number 302797 grommet.
Follow the kit instructions for installing the power supply cord.
Power supply cord must plug into a mating 3 prong, grounded
outlet, located in the cabinet next to the dishwasher opening.
Outlet must meet all local codes and ordinances.
INSTALLATIONINSTRUCTIONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect
power.
2. Turn off water supply.
1=
Follow the steps in the section if you are installing the
dishwasher in an existing cabinet opening with utility
hookups.
If you are installing the dishwasher
in a cabinet opening that
does not have utility hookups, follow the steps under "Prepare
cabinet opening where there are no existing utility hookups"
section.
Check that the water line reaches to the front left-hand side of
the opening where the water connection will be made.
........ .............
....
A. Water line
B. Direct wire
2. Check that the direct wire reaches to the front right-hand side
of opening where the electrical connection will be made.
If the water line and direct line wire reach far enough into the
opening, proceed to the next section, "Install the Drain Hose." If
they do not reach far enough, follow the steps under "Prepare the
Cabinet Opening Where There are no Existing Utility Hookups."
Install the Drain Hose
IMPORTANT: Always use a new drain hose even when installing a
new replacement dishwasher.
1. Drill a 1V2" (3.8 cm) diameter hole in the cabinet wall or floor on
the side of the opening closest to the sink.
2. Connect drain hose to waste tee or waste disposer using one
of the following methods:
•
Option 1, Waste disposer-
with air gap
•
Option 2, No waste disposer-
with air gap
•
Option 3, Waste disposer-
no air gap*
•
Option 4, No waste disposer-
no air gap*
*An air gap is recommended.
Helpful Tip: To reduce the vibration of the hose, keep the hose
away from the floor and the edge of the hole where it passes
through the cabinet.