Gardena 2315 Manuel d'utilisation - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Gardena 2315. Gardena 2315 7 pages.

Imprimer la page

GARDENA Accu Standard

1. Technical Data

Accu Standard

Accu

3 NC à 1.2 V = 3.6 V (1.2 Ah)

Mains connections for

charging device

230 V / 50 Hz

Charging time (with empty cells)

20 hours

Usual charging time

14 hours

Approx. running time

(with fully charged cells)

30 min. (depending on grass to be cut)

Approx. cutting performance

600 m (depending on grass to be cut)

Lawn blade

8 cm cutting width, non-stick coated

Working area related emission

characteristic value L

67 dB (A)

p A

Vibrations a

< 2.5 ms

vhw

1) Measuring method according to

prEN 50260 -1

2. Information Concerning the Instructions

Read these instructions care-

For safety reasons, chil-

fully and observe the informa-

dren under the age of 16

tion contained in them.

as well as people, who are not

Acquaint yourself with the use

acquainted with the

of the unit and observe the

instructions should not use

safety instructions.

these Accu Shears.

3. Proper Use

The GARDENA Accu Standard

It is absolutely necessary to

has been designed for the cut-

observe the manufacturer's

ting of grass edges and small

operating instructions to ensure

grass surfaces in private gar-

the unit's proper functioning.

dens / hobby area.

The operating instructions

also contain advice for service,

maintenance and repair.

4. Initial Operation

( ill. A)

Before first operation and with

Attention : make sure

empty cells charge the Shears

that the mains voltage

for approx. 20 hours. The usual

is correct. Charge only in a

charging time is about 14 hours.

dry place ! The cells discharge

For this, just insert charging

by themselves when stored

cable

into the charging

for a longer period of time.

socket

of the shears, and

Therefore, the unit should

charging unit

into the wall

be recharged before each

socket.

operation.

- 2

Keep these instructions in

a safe place.

Caution! For safety

reasons, the unit should

not be used for cutting

hedges or chopping in the

sense of composting.

4.1. Using the Shears (ill. B)

The area to be cut should first

be cleared of stones and other

solid objects. The safety stop

switch

prevents your

GARDENA Shears from being

switched on unintentionally. For

operation of the Accu Shears,

push safety stop switch

the left to release (position "I").

Then press on starting switch

Cutting grass :

Simply slide the shears along

the turf on their sliding sled

This ensures a constant even

cutting height. The large contact

surface makes the shears easy

to handle. The best cutting

results are obtained with dry

grass. However, there is no elec-

trical danger when the grass is

for instance damp.

5. Assembly of the Grass Cutting Blades

Assembly of the Extension Handle

Please only use the original

GARDENA grass cutting

blades for Accu Standard,

Art. No. 2345.

Before (dis-)assembly of

the grass cutting blades,

push safety stop switch

to lock starting switch – to the

right (position "0") and dis-

connect from the mains sup-

ply if necessary (charging pro-

cess). Risk of injury !

Loosen screws

and take off

grass cutting blades. When in-

stalling the new grass cutting

blades ensure that upper blade

is situated exactly in the mid-

dle of the lower blade

the cam gear

so that

the marking line

is pointing

exactly forwards.

6. Maintenance, Service, Storage

For safety reasons, be-

fore (dis)assembly of

the grass cutting blades, push

safety stop switch

starting switch – to the right

(position "0") and disconnect

from the mains supply if nec-

essary (charging process).

Maintenance of the blades

The blades of the GARDENA

Accu Shears are non-stick coat-

ed. The blades should always

When cutting power drops

considerably, recharge shears

immediately to prevent cells

from becoming completely

empty.

Lock Accu Shears after each

use ( push safety stop switch

to the right on position "0").

The safety devices in-

stalled by the manufac-

(ill. C)

(ill. B, D)

First guide the blade under-

neath the blade pegs

of the

carriage. Make sure that the

cam

snaps into the connect-

ing link

. Tighten the screws

Please note :

.Before inserting new blades,

–

clear the gear area. Lubricate

the gear wheels with some

non-corrosive grease (Vase-

line).

.Always lightly oil the blades

before and after use (do not

grease!).

Assembly of Extension

Handle (ill. B, D)

Cutting lawn edges without

kneeling or bending down. The

. Turn

Accu Shears are pushed over

lawn on their sliding sled by

means of the GARDENA Exten-

sion Handle (Art. No. 2354).

( ill. E, F )

be sharp in order to obtain good

cutting results. They can be

sharpened by using a sharpen-

– to lock

ing stone. We especially recom-

mend always immediate removal

of notches and burrs which

could be caused by stones.

The possibility of separating the

upper and lower blades (ill. E)

makes sharpening especially

easy.

The shears should be cleaned

thoroughly before and after use.

turer must not be removed

and / or bridged, eg: by fasten-

ing down the starting lockout

of the pushbutton switch on

the handle as there is danger

of injury because the tool will

not switch off automatically.

Attention ! Blades may

cause serious injury !

By doing so, the handle or shears

can be swivelled up to 45° on

either side:

.Push safety stop switch

to the right in order to lock

Accu Shears (position "0").

.Push the extension handle

into the mounting point

at the desired angle until the

catch locates.

.Push the handle plug

into

the handle socket

. The

unit is ready for operation.

.Only release safety stop

switch

on the handle and

press starting switch

.Before disassembly of the

extension handle, remove

plug of handle socket

press release button

and

pull handle out.

A few drops of oil (e.g. sewing

machine oil) applied to the

blades improve the cutting per-

formance. However, never

grease the blades.

For a constant clean cut it is

necessary to remove grass

residues and dirt even between

upper and lower blade. There-

fore, disassemble and clean the

blades also at this place from

time to time.