Garmin CATALYST Manuel du propriétaire - Page 5
Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Garmin CATALYST. Garmin CATALYST 18 pages. Driving performance optimizer
Également pour Garmin CATALYST : Manuel du propriétaire (34 pages)
Imprimer la page
Getting started
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
This device is only intended for recreational use in a circuit
environment. Never use this device on public roads. Failure to
follow this warning may result in an accident causing property
damage, serious personal injury or death. You are responsible
for using this device in a safe and prudent manner.
The first time you turn on your device, it guides you through the
initial setup steps with on-screen prompts. You should complete
these steps before using the device for the first time.
1
Turn on the device and follow the on-screen instructions.
2
Update your device software
‑ Fi Network, page
Wi
8).
Installation
Installing the Magnetic Mount in Your
Vehicle
This product contains a lithium-ion battery. To prevent the
possibility of personal injury or product damage caused by
battery exposure to extreme heat, store the device out of direct
sunlight.
Both the device and its mount contain magnets. Under certain
circumstances, magnets may cause interference with some
internal medical devices and electronic devices, including
pacemakers, insulin pumps or hard drives in laptop computers.
Keep the device away from medical devices and electronic
devices.
1
Clean and dry your windscreen and the suction cup with a
lint-free cloth.
2
Press the suction cup to the windscreen and flip the lever
3
Connect the ball of the suction cup mount
the powered magnetic mount
.
4
Connect the double-ball link
5
Tighten the knobs on both double-socket arms slightly.
6
If necessary, rotate the powered magnetic mount so the
Garmin
logo faces right-side up and adjust the mount for
®
better viewing and operation.
7
Tighten the knobs to secure the mount.
Connecting the Mount to Vehicle Power
1
Plug the mini-USB end of the power cable
USB port
on the powered mount.
Getting started
WARNING
(Updating Software Using a
WARNING
and the ball of
to the double-socket arms
to both double-socket arms.
into the mini-
2
Plug the power cable into the included vehicle power adapter
.
3
Plug the vehicle power adapter into the power outlet in your
vehicle.
4
If necessary, turn on the vehicle ignition switch to provide
power to the power outlet in your vehicle.
Bare Wire USB Cable
Garmin strongly recommends having an experienced installer
with the proper knowledge of electrical systems install the
device. Incorrectly wiring the power cable can result in damage
to the vehicle or the battery and can cause bodily injury.
The device includes a bare wire power adapter for use in
vehicles that are not equipped with a CLA power outlet. You can
also use this cable in applications where a hardwired permanent
power source is preferred. The device must be mounted in a
suitable and secure location in your vehicle, based on available
power sources and safe cable routing.
Device mini-USB connector
10 to 30 Vdc system input power (red)
System ground (black)
.
Camera Mounting Considerations
The first time you turn on your device, it provides information to
help you mount the camera. The camera affixes to the
windscreen using the included adhesive mount. The adhesive
mount is difficult to remove after it is installed. You should
carefully consider the mounting location before you install the
mount.
• Do not mount the camera in a location that interferes with the
driver's view of the road.
• You should choose a mounting location that provides the
camera with a clear view of the road ahead.
• You should choose a mounting location that is as high as
possible on the centre of the windscreen.
• You should verify the area of the windscreen in front of the
camera is cleared by the windscreen wipers.
• You should avoid placing the camera behind a tinted area of
the windscreen.
Installing the Polarising Filter on the Camera
The camera comes with a polarising filter pre-installed over the
lens to help reduce glare from your windshield. If you remove
the polarising filter, you can re-install it.
Do not rotate the lens cover while it is installed on the camera.
1
Position the filter so the line on the outer rim is facing up.
WARNING
NOTICE
1