Garmin Reactor 40 Manuel d'instructions d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Garmin Reactor 40. Garmin Reactor 40 11 pages. Mechanical
Également pour Garmin Reactor 40 : Manuel d'instructions d'installation (13 pages), Manuel d'instructions d'installation (29 pages), Manuel de configuration (8 pages), Manuel d'instructions d'installation (25 pages)
Imprimer la page
Item Description
Important Considerations
CCU
You can mount the CCU in a non-submerged
location near the center of the boat, in any
orientation
Considerations, page
Mount the CCU away from sources of magnetic
interference.
ECU power
You must connect the ECU to a 12 to 24 Vdc
cable
power source. To extend this cable, use the
correct wire gauge
page
4).
CCU cable
To extend this cable to reach the ECU, you may
need to use cable extensions (sold separately)
(CCU Mounting and Connection Considerations,
page
1).
You must connect this cable to the alarm and the
Shadow Drive valve.
Pump
This diagram shows only the electrical
connections for the pump (sold separately).
Detailed installation instructions are included with
the pump.
Alarm
The alarm provides audible alerts from the
autopilot system, and you should install it near
the primary helm station
page
5).
Shadow Drive
You must install the Shadow Drive valve properly
valve
in the hydraulic steering line, and connect it to
the CCU cable
Valve, page
Component Layout
Single-Helm Layout
NOTE: This diagram is for planning purposes only. If needed,
specific connection diagrams are included in the detailed
installation instructions for each component.
Hydraulic connections are not shown in this diagram.
Item Description
Important Considerations
Helm control
A dedicated helm control is not included in all
autopilot packages. If you install the autopilot
without a dedicated helm control, the autopilot
CCU must be connected to the same NMEA
2000 network as a compatible Garmin
chartplotter to configure and control the autopilot
system.
Pump
ECU
12 to 24 Vdc
You must connect the ECU to a 12 to 24 Vdc
battery
power source. To extend this cable, use the
correct wire gauge
page
4).
You must connect the NMEA 2000 power cable
to a 9 to 16 Vdc power source.
(CCU Mounting and Connection
1).
(Power Cable Extensions,
(Installing the Alarm,
(Installing the Shadow Drive
5).
(Power Cable Extensions,
Item Description
Important Considerations
CCU
You can mount the CCU in a non-submerged
location near the center of the boat, in any
orientation
Considerations, page
Mount the CCU away from sources of magnetic
interference.
NMEA 2000
You must connect the helm control or compatible
network
Garmin chartplotter and the CCU to a NMEA
2000 network using the included T-connectors
(NMEA 2000
page
2).
If there is not an existing NMEA 2000 network on
your boat, you can build one using the supplied
cables and connectors
2000 Network for the Autopilot System,
page
5).
Dual-Helm Layout Guidelines
NOTE: This diagram is for planning purposes only. If needed,
specific connection diagrams are included in the detailed
installation instructions for each component.
Hydraulic connections are not shown in this diagram.
Item Description
Important Considerations
Helm control
A dedicated helm control is not included in all
autopilot packages. If you install the autopilot
without a dedicated helm control, the autopilot
CCU must be connected to the same NMEA
2000 network as a compatible Garmin
chartplotter to configure and control the autopilot
system.
12 to 24 Vdc
You must connect the ECU to a 12 to 24 Vdc
battery
power source. To extend this cable, use the
correct wire gauge
page
4).
You must connect the NMEA 2000 power cable
to a 9 to 16 Vdc power source.
Pump
ECU
NMEA 2000
You must connect the helm control or compatible
network
Garmin chartplotter and the CCU to a NMEA
2000 network using the included T-connectors
(NMEA 2000
page
2).
If there is not an existing NMEA 2000 network on
your boat, you can build one using the supplied
cables and connectors
2000 Network for the Autopilot System,
page
5).
CCU
You can mount the CCU in a non-submerged
location near the center of the boat, in any
orientation
Considerations, page
Mount the CCU away from sources of magnetic
interference.
(CCU Mounting and Connection
1).
®
Connection Considerations,
(Building a Basic NMEA
(Power Cable Extensions,
Connection Considerations,
®
(Building a Basic NMEA
(CCU Mounting and Connection
1).
3