Indesit DIFP 28T9 Manuel d'utilisation - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Indesit DIFP 28T9. Indesit DIFP 28T9 16 pages.
Imprimer la page- 1. Table of Contents
- 2. Precautions and Advice
- 3. Product Data
- 4. Installation
- 5. Electrical Connection
- 6. Description of the Appliance
- 7. Refined Salt and Rinse Aid
- 8. Loading the Racks
- 9. Detergent and Dishwasher Use
- 10. Wash Cycles
- 11. Special Wash Cycles and Options
- 12. Care and Maintenance
- 13. Troubleshooting
- 14. Product Guarantee and Repair Information
Electrical Connection
Electrical Connection
GB
If your appliance is supplied with a 13 amp. fused plug it can
be plugged into a 13 amp socket for immediate use. Before
using the appliance please read the instruction below.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colours as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
Removing the plug:
Ifyour appliance has a non-rewireable moulded plug and you
should wish to remove it to re-route the mains cable through
partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
- the mains cable is wired directly into a 13 amp cable
outlet,
with BS 5733) which
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative
plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
CAUTION:
- Once the appliance has been installed, the electrical plug
and socket should remain accessible.
- The Company shall not be held responsible for any in-
cidents that occur if these regulations are not observed.
6
controlled by a switch, (in compliance
is accessible without moving the
- Earth
- Neutral
- Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market "E" or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked "L" or coloured Red.
Connect Blue wire to terminal marked "N" or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15 amp
fuse, either in the plug or adaptor or at the distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with
the following code:
BLUE
"NEUTRAL" ("N")
BROWN
"LIVE" ("L")
GREEN AND YELLOW
"EARTH" ("E") or
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above.