A-Neuvideo ANI-2PIP-LOGO Manuel d'instruction - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} A-Neuvideo ANI-2PIP-LOGO. A-Neuvideo ANI-2PIP-LOGO 15 pages. 2x1 hdmi multiviewer
Également pour A-Neuvideo ANI-2PIP-LOGO : Manuel d'instruction (20 pages)

Imprimer la page

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your

equipment. Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain,

water and excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean

dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they

are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and

plugs, convenience receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken

so that the means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper

AC voltage is not covered by any warranty.

10.

Turn power off and disconnect unit from AC current before making connections.

11.

Never hold a power switch in the "ON" position.

12.

This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.

Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.

13.

Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may

impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used

in an extremely dusty or smoky environment, the unit should be periodically "blown free" of foreign dust and matter.

14.

To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all

servicing to qualified service personnel. There are no user serviceable parts inside.

15.

When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting

cables to other devices.

16.

Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17.

The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18.

Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship

the unit, use only the original factory packing.

19.

Service Information Equipment should be serviced by qualified service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain.

D. The equipment does not appear to operate normally, or exhibits a marked change in performance.

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY IN-

STRUCTIONS CONTAINED WITHIN THIS MANUAL.

NEUVIDEO

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power

supply. Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.

• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow

for sufficient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for

any infringements of patents or other rights of third parties which may result from its use.

We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update

or to keep current the information contained in this document.

We reserve the right to make improvements to this document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated

into any language or computer file, in any form or by any means — electronic, mechanical, magnetic, optical, chemical,

manual, or otherwise — without the express written permission and consent.

Version 1.2 MAR 2020

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.