Billi 926065 Manuel d'installation - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Billi 926065. Billi 926065 7 pages. Dispenser options: xl and mixer tap, al
Également pour Billi 926065 : Manuel de l'utilisateur (9 pages)

Imprimer la page

Unpacking your Billi OmniOne

Before commencing installation, carefully check for any damage to cartons, appliance metalwork, pipework fittings and electrical power cord. If damage is
found, please photograph and record details for use if a claim is to be made.

Included Components

Before commencing installation, identify the following components:
1.
Underbench module
2.
Pre-installed filter cartridge
3.
Dispenser kit
4.
Plus mixer tap kit (Billi OmniOne Plus 9 only)
5.
Power cable
6.
Installation kit containing:
a. Drain tube assembly
b. 600mm flexible braided hose
c. Black Ø6mm PE tube
d. Drain connection kit containing:
i. Instruction sheet
ii. Hex key
iii. Drain boot
iv. Drain adaptor
v. Drain clamp
vi. Spring clamps x3

Installation Requirements

Determine Unit Location
Plan the installation carefully, taking into consideration dispenser tube lengths, position of power and water outlets, and access for servicing. The Billi
OmniOne is to be installed indoors only and must be installed on a level surface with the display panel facing to the front of the cupboard. Refer to Diagram 1
for a typical installation scenario.
Power Requirements
A 10 amp single 3 pin GPO is required within the cupboard. A dedicated circuit should be provided and must be fitted with an earth leakage protection device
(RCD). An externally fitted RCD device is acceptable.
Water Supply
The Billi OmniOne must only be connected to a cold water supply. A 1/2" BSP stop tap (not supplied) is to be installed in an easily accessible location within 600mm
of the Billi OmniOne water supply inlet. A certified pressure limiting valve with internal dual check valve for backflow prevention is incorporated in the appliance. Do
not fit an additional pressure limiting valve or dual check valve. A second 1/2" BSP water supply with stop tap is also required for Billi OmniOne Plus 9.
Inlet water supply requirements:
Dynamic pressure: Min. 250kPa – Max. 1000kPa
Water temperature: Min. 5°C – Max. 30°C
Do not install with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system.
Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
Drainage
The Billi OmniOne requires a drainage point, such as a dishwasher nipple. Use the supplied drain boot to connect to a dishwasher nipple, or the supplied clamp-
on drain adaptor to connect directly to a waste pipe. The clamp-on drain adaptor must be installed above the water seal on the sink side of the water trap.
Installation Footprint
The Billi OmniOne has the following dimensions:
Height
Width
Depth
355mm
395mm
495mm
A minimum cupboard depth of 520mm is required for installation. No cupboard ventilation is required, however a small air gap of 10mm around each side is
recommended. 150mm of clearance is recommended above the appliance for accessibility.
4
7.
CO
cylinder
2
8.
CO
regulator
2
9.
Manual kit containing:
a. User guide
b. Installation guide
c. Warning label
d. New purchase information sheet
e. Warranty sheet
Installation Requirements cont.
Power
outet
Stop tap (installed by
plumber) Max. 600mm
from unit)
Diagram 1

Installing the XL Dispenser

IMPORTANT: This Billi appliance is to be installed by a licensed tradesperson in accordance with AS/NZS 3500.1 and AS/NZ 3500.2 and in compliance with
applicable state regulatory requirements. For correct operation of this appliance, it is essential to observe the manufacturer's instructions.
Components in Dispenser Kit
Before commencing installation, identify the following components:
1.
Dispenser
2.
Large D-washer
1.
Determine Dispenser Location
The XL dispenser can be installed on a surface 1mm –48mm thick and requires a hole size of ø35mm. All tube and signal cable lengths are 800mm and
connect to top rear of underbench module.
Refer to Diagram 2 for a base template that may be cut out to assist in positioning, and Diagram 3 for dimensions of dispenser. Ensure to leave sufficient room
for the safety lock button on rear of dispenser head.
2.
Cut ø35mm Hole in Sinktop or Benchtop
a)
Stainless Steel Sinktop
A suitable ø35mm hole punch (Part no: 857901) is available as an accessory from Billi Australia Pty Ltd. If possible, cut hole with die mounted below the
sinktop surface so burrs are pulled downwards. Alternatively, remove burrs and radius edge of hole with a fine file.
b)
Timber/Laminate Benchtop
Take care to avoid a large chips breaking as the drill breaks through underside surface. We recommend drilling a small pilot hole through the benchtop,
partially drilling ø35mm hole from underneath, and then completing drilling hole from above.
*For all stone benchtops we recommend you use a certified stone mason to pre-drill the hole.
Tubing
150mm
removed
recommended
for clarity
clearance
5