Aqua Quip AQUA-STAR Instructions d'installation - Page 4

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} Aqua Quip AQUA-STAR. Aqua Quip AQUA-STAR 4 pages.

Imprimer la page
Pool Light Installation
10 Clean any debris that may have entered the
Housing and Adjustable Dress Ring during pool
construction. Insert and coil up excess cable into
the Housing. Aqua-Star Halogen self-locates onto
the Adjustable Dress Ring, use two 5/8" CSK
stainless steel screws provided to attach pool light
to Adjustable Dress Ring, do not overtighten.
Blue and green lens covers are included, fit either
onto the light before securing light to the Adjustable
Dress Ring.
11 Fit optional Polished Stainless Steel Trim Ring if
required, using the 7/8" CSK stainless steel screws
provided in the Stainless Steel Trim Ring Kit.
12 Only turn pool light on when completely submerged
under water.
ELECTRICAL
CONNECTION AND
OPERATION
Install Light(s) and Transformer(s)
in accordance with AS/NZS
3000:2007 as amended.
Transformers have either 2 or 4
secondary outputs, each being
12v 50VA, refer to Diagram 4.
4
A Q U A - S T A R H A L O G E N L I G H T S F O R C O N C R E T E P O O L S – I N S T A L L AT I O N I N S T R U C T I O N S & O W N E R S M A N U A L
AQUA-STAR HALOGEN
POOL LIGHT INSTALLATION
Ensure sufficient
cable length is
wound up inside the
Housing.
Diagram 3
Rainbow Pool Products
PO Box 2388, Mansfield Qld 4122
Automatic Pool Cleaners (Australia) Pty Ltd
Telephone STD 61-7-3849 5385
40 Percy Street, Auburn NSW 2144
Facsimile STD 61-7-3849 5384
Ph: 02 9643 8338 Fax: 02 9643 8448
www.aquaquip.com.au
Web: www.rainbowpoolproducts.com.au
AQUA-STAR GLOBE CHANGING
INSTRUCTIONS
1) Unscrew the 2 stainless steel screws, remove stainless
steel trim ring and/or coloured lens if fitted.
2) Float the light to the surface and place on deck.
3) Grip the rear black nut with multi grips or use a
screwdriver through the two holes in the black nut and
¼ turn anticlockwise whilst holding the white body of the
light. This will remove the nut from the body, exposing
the globe.
4) Remove existing globe by gently pulling the top of the
reflector, do not pull on the glass. Replace the globe
using a 12v 50w MR16 Globe, 55-60 degree beam.
Never touch the glass when replacing the globe.
5) Replace and lubricate the nut o-ring. The replacement
and lubrication of this o-ring is necessary any time the
Aqua-Star light is disassembled. Only use silicone based
lubricants.
6) If ceramic lamp holder is damaged or corroded, then it
should be removed using long nosed pliers. The male
spades of the new ceramic lamp holder will push into
the female spades. Replacement ceramic lamp holders
are available in kit form.
7) To re-insert nut into body. Place light body onto folded
towel on ground with clear diffuser facing down. Align
the mark on the nut with the alignment mark on the
body, firmly push nut into body and ¼ turn clockwise.
8) Excess cable can be loosely wrapped around the body
and/or inserted into the rear of the housing.
9) Remount the light (and coloured lens and stainless steel
trim ring if fitted) to the dress ring using the 2 stainless
screws. Fully submerge before operating.
TRANSFORMERS
Diagram 4 – Transformers
APL502 and
APL 512 run up to
2 x 50VA lights.
COPYRIGHT AUTOMATIC POOL CLEANERS (AUSTRALIA) PTY LTD
LIGHTS FOR
CONCRETE POOLS
APL504 and APL514 run
up to 4 x 50VA lights.
ASCM4p_0112