Aqua Quip AQUA-STAR Istruzioni per l'installazione - Pagina 4

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Illuminazione della piscina Aqua Quip AQUA-STAR. Aqua Quip AQUA-STAR 4.

Stampa la pagina

Pool Light Installation

10 Clean any debris that may have entered the

Housing and Adjustable Dress Ring during pool

construction. Insert and coil up excess cable into

the Housing. Aqua-Star Halogen self-locates onto

the Adjustable Dress Ring, use two 5/8" CSK

stainless steel screws provided to attach pool light

to Adjustable Dress Ring, do not overtighten.

Blue and green lens covers are included, ﬁt either

onto the light before securing light to the Adjustable

Dress Ring.

11 Fit optional Polished Stainless Steel Trim Ring if

required, using the 7/8" CSK stainless steel screws

provided in the Stainless Steel Trim Ring Kit.

12 Only turn pool light on when completely submerged

under water.

ELECTRICAL

CONNECTION AND

OPERATION

Install Light(s) and Transformer(s)

in accordance with AS/NZS

3000:2007 as amended.

Transformers have either 2 or 4

secondary outputs, each being

12v 50VA, refer to Diagram 4.

A Q U A - S T A R H A L O G E N L I G H T S F O R C O N C R E T E P O O L S – I N S T A L L AT I O N I N S T R U C T I O N S & O W N E R S M A N U A L

AQUA-STAR HALOGEN

POOL LIGHT INSTALLATION

Ensure sufﬁcient

cable length is

wound up inside the

Housing.

Diagram 3

Rainbow Pool Products

PO Box 2388, Mansfield Qld 4122

Automatic Pool Cleaners (Australia) Pty Ltd

Telephone STD 61-7-3849 5385

40 Percy Street, Auburn NSW 2144

Facsimile STD 61-7-3849 5384

Ph: 02 9643 8338 Fax: 02 9643 8448

Email: [email protected]

www.aquaquip.com.au

Web: www.rainbowpoolproducts.com.au

AQUA-STAR GLOBE CHANGING

INSTRUCTIONS

1) Unscrew the 2 stainless steel screws, remove stainless

steel trim ring and/or coloured lens if ﬁtted.

2) Float the light to the surface and place on deck.

3) Grip the rear black nut with multi grips or use a

screwdriver through the two holes in the black nut and

¼ turn anticlockwise whilst holding the white body of the

light. This will remove the nut from the body, exposing

the globe.

4) Remove existing globe by gently pulling the top of the

reﬂector, do not pull on the glass. Replace the globe

using a 12v 50w MR16 Globe, 55-60 degree beam.

Never touch the glass when replacing the globe.

5) Replace and lubricate the nut o-ring. The replacement

and lubrication of this o-ring is necessary any time the

Aqua-Star light is disassembled. Only use silicone based

lubricants.

6) If ceramic lamp holder is damaged or corroded, then it

should be removed using long nosed pliers. The male

spades of the new ceramic lamp holder will push into

the female spades. Replacement ceramic lamp holders

are available in kit form.

7) To re-insert nut into body. Place light body onto folded

towel on ground with clear diffuser facing down. Align

the mark on the nut with the alignment mark on the

body, ﬁrmly push nut into body and ¼ turn clockwise.

8) Excess cable can be loosely wrapped around the body

and/or inserted into the rear of the housing.

9) Remount the light (and coloured lens and stainless steel

trim ring if ﬁtted) to the dress ring using the 2 stainless

screws. Fully submerge before operating.

TRANSFORMERS

Diagram 4 – Transformers

APL502 and

APL 512 run up to

2 x 50VA lights.

LIGHTS FOR

CONCRETE POOLS

APL504 and APL514 run

up to 4 x 50VA lights.

ASCM4p_0112