Allmatic AS24 Manuel d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Allmatic AS24. Allmatic AS24 10 pages. Control unit for 1-2 motors 24vdc
Imprimer la page
4. Preliminary checks
Before connecting the control panel to the power supply, check all wirings which have been carried out. In particular check that there are no
damaged wires, short-circuits between wires and that all accessories are connected to the terminal board in the points shown on the diagram on
the previous page. Once the power supply is connected check that:
1.
The POWER LED is constantly lit.
2.
The normally closed inputs must have the corresponding LED lit. The LED must turn off when the input contact is opened.
3.
Check that the radio module is inserted and working.
4.
Set the dipswitch 1 on ON
5.
Check the motor connection by following the procedure as described below
Dipswitch position
Release the BLUE button. Press and keep pressed
again the BLUE one (P2). Wing 2 should close. Bring
it in close position then release the button.
Dipswitch position
SI
PLEASE NOTE: During these movements the photocells, the radio and the buttons are NOT active.
5. Remote control learning
Memorize at least one 2-key remote control. In order to program the wing stroke use a 2-key remote control. During normal operation however, (i.e.
not during programming) the 1st memorized key carries out the step by step function (opening and closing of the gate), the 2
pedestrian opening (complete opening of the 1
Dipswitch position
Press the remote control's 1st key. The flashing
signal emits 2 flashes .
The remote control's 1st key is now memorized.
A
Press and release the RED button: The flashing
signal's LED is permanently lit.
Press the remote control's 2nd key. The flashing
signal emits 1 flash
The 2 buttons are now memorized and the
procedure ends. Repeat the procedure from
point « A » if you want to learn the button for the
courtesy light control.
6-1622372
rev.5 04/02/2016
Press and keep press the
RED button (P1): Wing 1 (the
beating one) must open.
SI
Release the RED button. Press and
keep pressed the BLUE one (P2).
Wing 2 should open.
SI
SI
Press and keep pressed again the
RED button (P1). Wing 1 should
close. Bring it in close position then
release the button.
st
rd
wing). The 3
Press and release the RED
button: The flashing signal's
LED is permanently lit .
SI
SI
SI
SI
ITA
ENG
If wing 1 does not move, check the wiring of motor
1 (terminals 18 and 19) and repeat the test.
If wing 1 closes, stop everything and invert the
NO
motor 1 wires (terminals 18 and 19).
If wing 2 moves, stop everything and invert motor 1
wires with motor 2 wires.
If wing 2 does not move, check the wiring of motor
2 (terminals 20 and 21) and repeat the test.
NO
If wing 2 closes, stop everything and invert the
motor 2 wires (terminals 20 and 21)
Check the wirings
NO
and repeat the test.
Check the wirings
NO
and repeat the test.
key operates the courtesy light.
Check that the dipswitch 1 and
NO
2 are set OFF. repeat the test
If flashing signal has emitted 1 flash, the pressed key had
already been memorized and it is possible to continue with the
procedure. Otherwise, check that the remote control is working,
NO
that it has the same decoding settings of the control panel and
that the radio module is correctly inserted. Then repeat the test
Check that the dipswitch 1 and
NO
2 are set OFF. repeat the test
Check that the remote control works, that it has the same
decoding set in the control panel and that the radio mo-
NO
dule is inserted. Then repeat the test .
FRA
ESP
DEU
POR
nd
key carries out the
Pag 3 di 10