AccuMed CMS-50D Manuel de l'utilisateur - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} AccuMed CMS-50D. AccuMed CMS-50D 2 pages. Fingertip pulse oximeter
Également pour AccuMed CMS-50D : Manuel (14 pages)

Imprimer la page

4 Technical Specifications

1) Display Format: OLED Display;

SpO

Measuring Range: 0% - 100%;

Pulse Rate Measuring Range: 30 bpm - 250 bpm;

Pulse Wave Display: columniation display and the waveform display.

2) Power Requirements: 2 ×1.5V AAA alkaline batteries (or using the rechargeable battery instead),

adaptable range: 2.6V~3.6V.

3) Power Consumption: Lower than 30mA.

4) Resolution: 1% for SpO

and 1 bpm for Pulse Rate.

5) Measurement Accuracy: ±2% in stage of 70%-100% SpO

smaller

than 70%. ±2 bpm or±2% (select larger) for Pulse Rate.

6) Measurement Performance in Weak Filling Condition: SpO

correctly when pulse-filling ratio is 0.4%. SpO

larger).

7) Resistance to surrounding light: The deviation between the value measured in the condition of

man-made light or indoor natural light and that of darkroom is less than ±1%.

8) It is equipped with a function switch. The Oximeter can be powered off in case there is no finger in

the Oximeter for 5 seconds.

9) Optical Sensor

Red light (wavelength is 660nm, 6.65mW)

Infrared (wavelength is 880nm, 6.75mW)

5 Accessories

 One hanging rope;

 Two batteries (optional);

 One User Manual.

6 Installation

6.1 View of the Front Panel

Figure 2 Front view

6.2 Battery

Step 1. Refer to Figure 3 and insert the two AAA size batteries in the right direction.

Step 2. Replace the cover.

Please take care when you insert the batteries as improper insertion may damage the device.

Figure 3 Batteries installation

6.3 Mounting the Hanging Rope

Step 1. Put the end of the rope through the hole.

Step 2. Put another end of the rope through the first one and then tighten it.

Figure 4 Mounting the hanging rope

7 Operating Guide

1) Insert the two batteries in the correct direction, and then replace the cover.

2) Open the clip as shown in Figure 5.

Figure 5 Put finger in position

3) Put the patient's finger into the rubber cushions of the clip (make sure the finger is in the right

position), and then clip the finger.

4) Press the button once on front panel.

5) Do not shake the finger and keep the patient at ease during the process. It is not recommended for

the patient to be moving.

6) Get the information directly from screen display.

7) The button

has three functions. When the device is power off, pressing the button can turn it

on; when the device is powered on, pressing the button shortly can change direction of the screen;

when the device is powered on, long pressing the button can change brightness of the screen.

Fingernail and the screen should be on the same side.

8 Repairing and Maintenance

 Please change the batteries when the low-voltage displayed on the screen.

 Please clean the surface of the device before using. Wipe the device with medical alcohol first, and

then let it dry in air or clean it with dry clean fabric.

 Use the medical alcohol to disinfect the product after use prevents cross infection the next time it is

, and meaningless when stage being

and pulse rate can be shown

error is ±4%, pulse rate error is ±2 bpm or ±2% (select

used.

 Please take out the batteries if the oximeter is not in use for a long period of time.

 The best storage environment of the device is - 40ºC to 60ºC ambient temperature and no higher

than 95% relative humidity.

 Users are advised to calibrate the device periodically (or according to the calibrating program of

hospital). It also can be performed by the state-appointed agent or just contact us for calibration.

High-pressure sterilization cannot be used on the device.

Do not immerse the device in liquid.

It is recommended that the device should be kept in a dry environment. Humidity may reduce

the life span of the device, or even damage it.

9 Troubleshooting

Trouble

Possible Reason

The SpO

and

1. The finger is not properly

Pulse Rate cannot

positioned.

2. The patient's SpO

be displayed

normally

be detected.

1. The finger is not placed inside

The SpO

and

deep enough.

Pulse Rate are not

2. The finger is shaking or the

displayed stably

patient is moving.

1. The batteries are dead or

almost dead.

The device cannot

2. The batteries are not inserted

be turned on

properly.

3. The device is defective.

1. The device will power off

The display is off

automatically when it gets no

suddenly

signal within 5 seconds.

2. The batteries are almost dead.

10 Key of Symbols

Symbol

Type BF

Warning – See User Manual

The pulse oxygen saturation (%)

PRbpm

Pulse rate (bpm)

The battery voltage is insufficient (change the battery in time to avoid

inexact measurements)

1. No finger inserted

2. An indicator of signal inadequacy

Battery positive electrode

Battery cathode

1. Power switch

2. Change direction of the screen

3. Change brightness of the screen

Serial number

Alarm inhibit

WEEE (2002/96/EC)

IP22

International Protection

11 Function Specification

Display Information

The Pulse Oxygen Saturation(SpO

)

Pulse Rate(PR)

Pulse Intensity (bar-graph)

Pulse wave

SpO

Parameter Specification

Measuring range

0%~100%, (the resolution is 1%).

Accuracy

70%~100%:±2%, Below 70% unspecified.

Optical Sensor

Red light (wavelength is 660nm)

Infrared (wavelength is 880nm)

Pulse Parameter Specification

Measuring range

30bpm~250bpm (the resolution is 1 bpm)

Accuracy

±2bpm or±2% select larger

Pulse Intensity

Range

Continuous bar-graph display, the higher display indicates a stronger pulse.

Battery Requirement

1.5V (AAA size) alkaline batteries × 2 or rechargeable batteries

Battery Useful Life

Two batteries can work continually for 20 hours

Dimensions and Weight

Dimensions

Weight

Solution

1. Place the finger properly and try

again.

2. Try again; Go to a hospital for a

is too low to

diagnosis if you are sure the device

works correctly.

1. Place the finger properly and try

again.

2. Keep the patient calm and at rest.

1. Change batteries.

2. Reinstall batteries.

3. Please contact the local service

center.

1. Normal.

2. Change batteries.

Description

Display Mode

OLED

OLED bar-graph display

OLED

57(L) × 31(W) × 32(H) mm

About 50g (with the batteries)