CIOKS Adam link Manuel de l'utilisateur - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} CIOKS Adam link. CIOKS Adam link 2 pages. Power supply for effect pedals

Imprimer la page

Overview

Right side

On the right side of the enclosure you'll find the 4 outlets of the power supply as RCA sockets

which all are centre positive. Correct polarity for the pedal is achieved by using the right Flex

cable.

The red settings switch with two white knobs placed just to the right of the outlets should be

used to set the output voltage of outlets 3 and 4. The left knob is for setting of outlet 3, the

right one is for outlet 4.

Knob no. *

Function

Outlet 3

Outlet 4

* counting from left, opposite order of the white digits on the red switch (if you can see them)

Top

CIOKS logo has a red LED placed in the middle of the letter 'O'. When this LED is lit the

power supply is connected to mains and operates.

On top of the enclosure you see the output voltage and max. current rating of each outlet

printed just above the outlet sockets. The top figure is the voltage and the DC in the middle

line tells you it's a direct current outlet. Outlets with two possible voltage settings have both

values stated as 9/12. The bottom figures states the maximum current capability of each outlet

in mA.

The status of each isolated output is shown by a LED indicator also situated on top of the

enclosure just above the voltage figure. The function of this advanced and unique monitoring

feature is described in detail later on.

Left side

On the left side of the enclosure you'll find the AC power input connector, which is a C6 type

according to the IEC 60320 standard also used in many laptop adapters. On the same side as

the AC mains input you'll find the mains voltage selector switch and the fuse.

Mains voltage selector switch should be used for setting the correct mains voltage 115 or

230V. The Japanese version is made only for a 100V nominal mains voltage and has no mains

voltage selector switch.

The fuse is the only part which may be replaced by the user. In case it's blown, replace with a

5x20mm, T 200mA (slow blow/time lag) type.

Bottom

The four detachable rubber feet are situated on the bottom of the enclosure. On this same

surface you'll find 4 holes with metric M4 threads, which should be used for easy mounting of

Knob down

Knob up

9V DC

12V DC

9V DC

12V DC

the power supply to a pedalboard. Do not use screws, which would go further than 5mm inside

the unit. Have a look at the mounting guide on CIOKS web site.

Getting started

First make sure that the voltage value chosen on the voltage selector switch matches the mains

voltage in your wall socket. Connect the mains power cord to the power supply and mains.

Using the right Flex cable types connect your pedals to the outlets of power supply making

sure that the voltage and current is correct for every pedal.

Advanced LED Monitoring feature

Each isolated outlet has its individual LED status indicator. The indicator is fully lit in normal

operation of a particular outlet. Its light gets dim when you operate just on the edge of the

current limit. If you overload or short circuit an outlet, the respective LED indicator turns off.

The LED indicators of outlets 1, 2, 5 and 6 with selectable output voltages also show you the

voltage set by the settings switch. In case a higher voltage than the default 9V setting is

selected for a given outlet, its respective LED indicator will be lit with higher intensity than the

other indicators.

All indicators take into account the actual level of mains voltage when monitoring a possible

overload. The current limits for each outlet or section of the power supply are specified at

nominal level of the mains voltage. In Europe it's 230V, 120V in e.g. United States and 100V

in Japan. If the mains voltage is higher than nominal, you can draw more current from the

power supply than stated in the specifications. This would never be a problem. A more

common situation though, is when the mains voltage is lower than nominal. In such a case

maximum current ratings for each outlet or section might be diminished.

The advanced LED monitoring of each isolated outlet will alert you in case of an overload or

short circuit. If such a situation happens you know where to look to solve the problem.

A glance at the LED status indicators and you have proof of 100% clean power to your pedals.

Included accessories

Flex cables

CIOKS offers a great selection of different Flex cable types for connection your pedals to the

power supply. Below you see a list of the included Flex cables with your unit:

•

Type 1 – black with 5,5/2,1mm centre negative DC-plug

•

Type 5 – black with 3,5mm tip positive jack-plug

•

Type 1 – Split Flex (to power two pedals of one outlet)