Axxess AXDIS-FD3 Manuel d'instructions d'installation - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Axxess AXDIS-FD3. Axxess AXDIS-FD3 16 pages.

Imprimer la page

L.E.D. feedback

The (23) Red L.E.D. flashes represent what brand radio the AXDIS-FD3 believes it is connected to. Each flash

represents a different radio manufacturer. For example, if you are installing a JVC radio, the AXDIS-FD3 will

flash (5) times. Following is a legend that dictates which manufacturer corresponds to which flash.

L.E.D. feedback legend

1st flash is for Eclipse (Type 1) †

2nd flash is for Kenwood ‡

3rd flash is for Clarion (Type 1) †

4th flash is for Sony/Dual

5th flash is for JVC

6th flash is for Pioneer/Jensen

7th flash is for Alpine *

8th flash is for Visteon

9th flash is for Valor

10th flash is for Clarion (Type 2) †

11th flash is for Metra OE

12th flash is for Eclipse (Type 2) †

* Note: If the AXDIS-FD3 flashes Red (7) times, and you do not have an Alpine radio connected to

it, that means the AXDIS-FD3 does not detect a radio connected it. Verify that the 3.5mm jack is

connected to the correct steering wheel jack/wire in the radio.

** Note: Part number AXSWCH-PAR is required (sold separately). Also, the Parrot radio must be

updated to rev. 2.1.4 or higher through www.parrot.com.

† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to the

other Clarion radio type; same for Eclipse. The following section explains how to do this.

‡ Note: If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC radio,

change the radio type to a Kenwood. The following section explains how to do this.

STEERING WHEEL CONTROL SETTINGS

13th flash is for LG

14th flash is for Parrot **

15th flash is for XITE

16th flash is for Philips

17th flash is TBD

18th flash is for JBL

19TH flash is for INSANE

20TH flash is for MAGNADYNE

21ST flash is for BOSS

22ND flash is for AXXERA

23RD flash is for AXXERA (TYPE 2)

Attention: The Axxess Updater App can also be used to program the following (3) sub-sections

as well, pending that the interface has been initialized and programmed.

Changing radio type

If the LED flashes do not match the radio you have connected, you must manually program

the AXDIS-FD3 to tell it what radio it is connected to.

1. After (3) seconds of turning the key on, press and hold the Volume-Down button on the

steering wheel until the L.E.D. in the AXDIS-FD3 goes solid.

2. Release the Volume-Down button; the L.E.D. will go out indicating we are now in Changing

Radio Type mode.

3. Refer to the Radio Legend to know which radio number you would like to have

programmed.

4. Press and hold the Volume-Up button until the L.E.D. goes solid, and then release. Repeat

this step for the desired radio number you have selected.

5. Once the desired radio number has been selected, press and hold the Volume-Down button

on the steering wheel until the L.E.D. goes solid. The L.E.D. will remain on for about (3)

seconds while it stores the new radio information.

6. Once the L.E.D. goes off, the Changing Radio Type mode will then end. You can now test the

steering control wheel controls.

Note: If at any time the user fails to press any button for a period longer than (10) seconds,

this process will abort.

Continued on the next page

REV. 2/15/23 INSTAXDIS-FD3