Axxess AXDIS-FD3 Інструкція з монтажу Посібник з монтажу - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Обладнання для запису Axxess AXDIS-FD3. Axxess AXDIS-FD3 16 сторінок.
Друкувати сторінкуL.E.D. feedback
The (23) Red L.E.D. flashes represent what brand radio the AXDIS-FD3 believes it is connected to. Each flash
represents a different radio manufacturer. For example, if you are installing a JVC radio, the AXDIS-FD3 will
flash (5) times. Following is a legend that dictates which manufacturer corresponds to which flash.
L.E.D. feedback legend
1st flash is for Eclipse (Type 1) †
2nd flash is for Kenwood ‡
3rd flash is for Clarion (Type 1) †
4th flash is for Sony/Dual
5th flash is for JVC
6th flash is for Pioneer/Jensen
7th flash is for Alpine *
8th flash is for Visteon
9th flash is for Valor
10th flash is for Clarion (Type 2) †
11th flash is for Metra OE
12th flash is for Eclipse (Type 2) †
* Note: If the AXDIS-FD3 flashes Red (7) times, and you do not have an Alpine radio connected to
it, that means the AXDIS-FD3 does not detect a radio connected it. Verify that the 3.5mm jack is
connected to the correct steering wheel jack/wire in the radio.
** Note: Part number AXSWCH-PAR is required (sold separately). Also, the Parrot radio must be
updated to rev. 2.1.4 or higher through www.parrot.com.
† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to the
other Clarion radio type; same for Eclipse. The following section explains how to do this.
‡ Note: If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC radio,
change the radio type to a Kenwood. The following section explains how to do this.
STEERING WHEEL CONTROL SETTINGS
13th flash is for LG
14th flash is for Parrot **
15th flash is for XITE
16th flash is for Philips
17th flash is TBD
18th flash is for JBL
19TH flash is for INSANE
20TH flash is for MAGNADYNE
21ST flash is for BOSS
22ND flash is for AXXERA
23RD flash is for AXXERA (TYPE 2)
Attention: The Axxess Updater App can also be used to program the following (3) sub-sections
as well, pending that the interface has been initialized and programmed.
Changing radio type
If the LED flashes do not match the radio you have connected, you must manually program
the AXDIS-FD3 to tell it what radio it is connected to.
1. After (3) seconds of turning the key on, press and hold the Volume-Down button on the
steering wheel until the L.E.D. in the AXDIS-FD3 goes solid.
2. Release the Volume-Down button; the L.E.D. will go out indicating we are now in Changing
Radio Type mode.
3. Refer to the Radio Legend to know which radio number you would like to have
programmed.
4. Press and hold the Volume-Up button until the L.E.D. goes solid, and then release. Repeat
this step for the desired radio number you have selected.
5. Once the desired radio number has been selected, press and hold the Volume-Down button
on the steering wheel until the L.E.D. goes solid. The L.E.D. will remain on for about (3)
seconds while it stores the new radio information.
6. Once the L.E.D. goes off, the Changing Radio Type mode will then end. You can now test the
steering control wheel controls.
Note: If at any time the user fails to press any button for a period longer than (10) seconds,
this process will abort.
Continued on the next page
5
REV. 2/15/23 INSTAXDIS-FD3