Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Manuel - Page 16

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 19 pages. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Également pour Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion : Note d'installation (14 pages), Manuel de solution (17 pages), Note d'installation (46 pages), Livre blanc (19 pages), Description (1 pages), Bulletin d'information sur les produits (6 pages), Avis (4 pages), Fiche technique (9 pages), Fiche technique (18 pages), Livre blanc (18 pages), Manuel de configuration (8 pages), Note d'installation (28 pages), Manuel de dépannage (11 pages), Note d'installation (18 pages), Manuel de l'utilisateur (17 pages), Note d'installation (24 pages), Note d'installation (36 pages)

Imprimer la page
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Manuel
Cisco - Connecting a Terminal to the Console Port on Catalyst Switches
Mode 2: Switch is in the out position. Use this mode to connect a terminal to the console port
using the Catalyst 5000 family Supervisor Engine III console straight-through cable and an
appropriate adapter for the terminal connection (cable and adapter are not provided). See
Port Mode 2 Signaling and

Console Port Mode 1 Signaling and Pinouts

This section provides the signaling and pinouts for the console port in mode 1 (port mode switch in the in
position).
DB-9 Adapter (for Connecting to a PC)
Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-9 female DTE adapter (labeled
"Terminal") to connect the console port to a PC running terminal emulation software.
lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and
the RJ-45-to-DB-9 female DTE adapter.
Table I-1: Port Mode 1: Console Port Signaling and Pinouts (DB-9 Adapter)
Console
RJ-45-to-RJ-45
Port
Rollover Cable
RJ-45
Signal
RTS
1¹
DTR
2
TxD
3
GND
4
GND
5
GND
6
DSR
7
CTS
8¹
¹Pin 1 is connected internally to Pin 8.
DB-25 Adapter (for Connecting to a Terminal)
Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-25 female DTE adapter (labeled
"Terminal") to connect the console port to a terminal.
asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25
female DTE adapter.
Table I-2: Port Mode 1: Console Port Signaling and Pinouts (DB-25 Adapter)
http://www.cisco.com/warp/public/473/9.html (16 of 19) [9/4/2003 12:36:03 PM]
Pinouts.
RJ-45-to-DB-9
RJ-45
Pin
Pin
8
8
7
6
6
2
5
5
4
5
3
3
2
4
1
7
Console
Terminal
Device
Adapter
DB-9 Pin
Signal
CTS
DSR
RxD
GND
GND
TxD
DTR
RTS
Table I-2
lists the pinouts for the
Console
Table I-1