Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 매뉴얼 - 페이지 16

{카테고리_이름} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 19 페이지. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion에 대해서도 마찬가지입니다: 설치 참고 사항 (14 페이지), 솔루션 매뉴얼 (17 페이지), 설치 참고 사항 (46 페이지), 백서 (19 페이지), 설명 (1 페이지), 제품 게시판 (6 페이지), 공지 사항 (4 페이지), 데이터시트 (9 페이지), 데이터시트 (18 페이지), 백서 (18 페이지), 구성 매뉴얼 (8 페이지), 설치 참고 사항 (28 페이지), 문제 해결 매뉴얼 (11 페이지), 설치 참고 사항 (18 페이지), 사용자 설명서 (17 페이지), 설치 참고 사항 (24 페이지), 설치 참고 사항 (36 페이지)

페이지 인쇄
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 매뉴얼
Cisco - Connecting a Terminal to the Console Port on Catalyst Switches
Mode 2: Switch is in the out position. Use this mode to connect a terminal to the console port
using the Catalyst 5000 family Supervisor Engine III console straight-through cable and an
appropriate adapter for the terminal connection (cable and adapter are not provided). See
Port Mode 2 Signaling and

Console Port Mode 1 Signaling and Pinouts

This section provides the signaling and pinouts for the console port in mode 1 (port mode switch in the in
position).
DB-9 Adapter (for Connecting to a PC)
Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-9 female DTE adapter (labeled
"Terminal") to connect the console port to a PC running terminal emulation software.
lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and
the RJ-45-to-DB-9 female DTE adapter.
Table I-1: Port Mode 1: Console Port Signaling and Pinouts (DB-9 Adapter)
Console
RJ-45-to-RJ-45
Port
Rollover Cable
RJ-45
Signal
RTS
1¹
DTR
2
TxD
3
GND
4
GND
5
GND
6
DSR
7
CTS
8¹
¹Pin 1 is connected internally to Pin 8.
DB-25 Adapter (for Connecting to a Terminal)
Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-25 female DTE adapter (labeled
"Terminal") to connect the console port to a terminal.
asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25
female DTE adapter.
Table I-2: Port Mode 1: Console Port Signaling and Pinouts (DB-25 Adapter)
http://www.cisco.com/warp/public/473/9.html (16 of 19) [9/4/2003 12:36:03 PM]
Pinouts.
RJ-45-to-DB-9
RJ-45
Pin
Pin
8
8
7
6
6
2
5
5
4
5
3
3
2
4
1
7
Console
Terminal
Device
Adapter
DB-9 Pin
Signal
CTS
DSR
RxD
GND
GND
TxD
DTR
RTS
Table I-2
lists the pinouts for the
Console
Table I-1