Argo AW22AL Manuel d'utilisation - Page 8

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Argo AW22AL. Argo AW22AL 12 pages. Split air conditioner system
Également pour Argo AW22AL : Manuel d'utilisation (12 pages)

Imprimer la page

NOTE

The air conditioner changes the operation mode (from cool to heat

or vice versa, if one of the following conditions occurs:

- ZONE A: changes if the difference between the room temperature

and the temperature set on the remote control unit is at least 3°C..

- ZONE B: changes if the difference between the room temperature

and the temperature set on the remote control unit is at least 1°C,

one hour after the compressor stop.

- ZONE C: never changes if the difference between the room

temperature and the temperature set on the remote control unit is

no more than 1°C.

DEHUMIDIFYING (DRY)

1. Set the MODE selector switch to "DRY"

2. Press the ON/OFF button and switch the air condioner ON.

3. Press the TEMP. buttons to set the desired temperature (the

temperature range is between 30 °C max. and 16 °C min.).

THE DISPLAY SHOWS THE SELECTED TEMPERATURE.

NOTE

Use DRY operation when you want to reduce the humidity in the

room.

Once the room temperature reaches the set level, the unit

repeats the cycle of turning on and off automatically.

During DRY operation, the fan speed is automatically set to low

or stops to prevent overcooling.

Dry operation is not possible if the indoor temperature is 15 °C

or less.

FAN ONLY

If you want to make air circulate without any temperature control,

follow these steps:

1. Set the MODE selector switch to "FAN"

2. Press the ON/OFF button and switch the air conditioner ON.

ADJUSTING THE FAN SPEED

AUTOMATIC

Simply set the FAN SPEED selector to the

. A microcomputer automatically controls the fan speed when the

AUTO mode is selected. When the air conditioner starts operating,

the difference between the room temperature and the set

temperature is detected by the microcomputer which then

automatically switches the fan speed to the most suitable level.

NOTE

In FAN Only mode the fan speed is adjusted automatically as in

cooling mode.

WHEN DIFFERENCE BETWEEN

ROOM TEMPERATURE AND SET

TEMPERATURE IS

Cooling and

dehumidifying modes:

Heating mode:

FAN SPEED

2 °C and over

High

Between 2 and 1 °C

Medium

Below 1 °C

Low

2 °C and over

High

Below 2 °C

Medium

NOTE

The above mentioned data make reference to the conditioner

operating when the sensor on the remote control unit is ON. (Refer

to temperature sensor selector). If the sensor on the indoor unit

is being used then actual operation will slightly differ from that

described in the above tables. (

control unit display).

MANUAL

If you want to manually adjust speed just set the FAN SPEED

selector as desired.

High speed

SLEEP MODE

The SLEEP mode enables you to save energy.

1. Set the MODE selector to cool, dry or heat.

2. Press the SLEEP button.

3. The

mark appears on the display. Press the SLEEP

button again to release the SLEEP function.

What does the SLEEP mode mean?

In this mode, the air conditioner will cool or heat the room to the

set temperature, and then the thermostat will make the unit pause.

After about 1 hour, the air conditioner will automatically reset the

set temperature as follows (also refer to graphs).

OPERATING MODE

Heating

Cooling and Dehumidifying

When the room temperature reaches the new set value, the

thermostat will cause the unit to pause. After about 1 hour the

temperature will be raised by 1 °C in cooling, or lowered by 1 °C

in heating. This enables you to save energy without sacrificing

your comfort.

position

COOLING AND DEHUMIDIFYING

Setting temperature

1°C

1 hour

) Sign shown on the remote

Med. speed

SET TEMPERATURE CHANGE

Lowered by 1 °C

Raised by 1 °C

Room temperature

1°C

1 hour

TIME

HEATING

COOL / DRY / HEAT / FAN

Setting temperature

1 C

1 hour

1 hour.

Low speed

Room temperature

1 C

TIME