Argo HI FLOOR DESIGN Mode d'emploi - Page 2
Parcourez en ligne ou téléchargez le pdf Mode d'emploi pour {nom_de_la_catégorie} Argo HI FLOOR DESIGN. Argo HI FLOOR DESIGN 5 pages. Electric convection heater
Imprimer la page
Use this convector only as outlined in this manual. Any other use not recommended by the manufacturer may cause
fire, electric shock or injury to persons.
Ensure that the mains voltage complies with that indicated on the convector data plate (220-240VAC/50Hz).
Remove the convector from its packaging and check that it is in good condition before use. Keep any plastic bags away
from children.
Check the cord and plug before using the convector to ensure that they have not been damaged during transport.
This convector is not a toy. Children should be adequately supervised to ensure that they do not play with the panel.
This convector is not suitable for use by persons (including children) with reduced physical, sensory or mental abilities,
or without the necessary experience and knowledge, unless they are adequately supervised and have been instructed
concerning use of the convector by a person responsible for their safety.
This convector is designed for domestic use. It must not be used for commercial or industrial purposes.
Disconnect the mains power when the appliance is not used or for cleaning operations.
To disconnect the convector, set the selector to 0 and remove the plug from the socket. Pull on the plug only. Do not
pull the cord.
Avoid placing fingers or foreign objects in the air inlet/outlet grilles, as this may lead to electric shock or fire and may
damage the convector. To avoid the risk of fire, do not block the grilles or tamper with them in any way while the
convector operates.
Do not use the convector if the cord or plug is damaged. If the power supply cord is damaged, it must be replaced by
the manufacturer, dealer or a similarly qualified person so as to avoid any safety risks.
Do not place any objects on the cord and do not bend it. During operation, the cord must be entirely unwound.
It is not advisable to use extension cords, as these may overheat and cause the risk of fire. Do not use a single
extension cord to operate more than one convector.
The convector heats up significantly during operation. Risk of burn. To avoid injury, do not allow skin to come into
contact with a hot surface. Use the handle to move the convector. Keep flammable materials, such as furniture,
cushions, blankets, paper, cloths, curtains and suchlike at least 1 m from the front and back
Do not immerse the cord, plug or any other element of the panel in water or other liquids.
Do not touch the plug or convector with wet hands.
Avoid using the convector in dusty environments or in the presence of flammable vapours (e.g. in workshops or
garages).
Do not place the convector above or near another heat source.
WARNING: AVOID COVERING THE CONVECTOR TO PREVENT IT FROM OVERHEATING.
The symbol below signals the above warning:
The convector may cause risk of fire if, while in operation, is covered by or comes into contact with flammable material
including curtains, drapery, blankets, etc. KEEP THE CONVECTOR AWAY FROM THESE MATERIALS.
Do not insert and avoid accidental insertion of any external objects into the ventilation or discharge outlets as this may
lead to electric shock, fire or damage the convector.
A convector contains parts that generate arcs or sparks. It must not be used in potentially dangerous areas such as
areas at risk of fire or explosion, or areas loaded with chemical substances or humidity.
Do not use the convector on soft surfaces such as beds, where the grilles may be covered. Always stand the convector
on a flat, stable surface when in operation, in order to prevent it from overturning. Arrange the cord in such a way that
the convector and other objects do not rest on it. Do not run the cord under carpets. Do not cover the cord with
blankets, carpets or similar materials. Place the cord far away from busy areas, or in a place where it cannot be
accidentally pulled-out.
This convector cannot be used in bathrooms, laundry rooms, next to a shower or swimming pool or in similar indoor
environments. Never position the convector where it may fall into a bath or other containers of water.
Never position the convector on a wet floor.
In any case, the adjustment knobs must never be accessible by anyone in a bath or shower.
Do not position the convector below an electric socket.
The socket must be earthed.
Do not allow the electric cord to touch the metal structure of the convector when it is hot or in operation, in order to
avoid the high temperatures ruining the cord.
Do not operate the convector outdoors. Do not use the convector in front of or near an open window.
V 05/11
GENERAL SAFETY INFORMATION
7