Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player Manuel d'installation - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player. Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player 8 pages. Owner's manual
Également pour Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player : Manuel (39 pages), Manuel du propriétaire (34 pages)

Imprimer la page

Installation

When connecting the external video component and the display

Audio input

Video input

External

video

component

(sold separately)

To audio outputs

Audio output

RCA cables

Multi-DVD Player

(sold separately)

To video output

Video output

RCA cable

Display with

(sold separately)

RCA input jacks

To video input

• It is necessary to set AV INPUT to VIDEO in SET UP when connecting the external

video component.

• It is necessary to set AV INPUT to M-DVD in SET UP when connecting a multi-DVD

player.

When using a display connected to rear video output

This product's rear video output is for connection of a display to enable passengers in the

rear seats to watch the DVD or Video CD.

WARNING:

• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while

Driving.

Note:

DIN Front/Rear-mount

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected

This unit can be properly installed

up properly, and the unit and the system work

either from "Front" (conventional DIN

properly.

Front-mount) or "Rear" (DIN Rear-

• Use only the parts included with the unit to ensure

mount installation, utilizing threaded

proper installation. The use of unauthorized parts

screw holes at the sides of unit chassis).

can cause malfunctions.

For details, refer to the following illus-

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

trated installation methods.

of the vehicle.

• Install the unit where it does not get in the driver's

Before installing the unit

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• Remove the frame and the hold-

• Do not install the display where it may (i) obstruct

er. (Fig. 14)

the driver's vision, (ii) impair the performance of

any of the vehicle's operating systems or safety

Pull out to remove the frame and then

features, including air bags, hazard lamp buttons or

loosen the screws (2 × 3 mm) to

(iii) impair the driver's ability to safely operate the

remove the holder. (When reattaching

vehicle.

the frame, point the side with a groove

• The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

downwards and attach it.)

— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,

the unit might not give its optimum performance.

(Fig. 12)

Fig. 11

30°

Fig. 12

• The cords must not cover up the area shown in the

figure below. This is necessary to allow the ampli-

fires to radiate freely. (Fig. 13)

Do not close this area.

Fig. 13

DIN Front-mount

Installation with the rubber bush

1. Decide the position of the side

brackets. (Fig. 15)

When installing in a shallow space,

change the position of side brackets. In

this case, stick conceal tape on parts

that protrude from the dashboard.

Side bracket

Flush surface screw (5 × 6 mm)

Holder

Screw (2 × 3 mm)

Frame

Fig. 14

2. Install the unit into the dash-

DIN Rear-mount

board. (Fig. 16)

After inserting the holder into the dash-

Installation using the screw holes on

board, then select the appropriate tabs

the side of the unit

according to the thickness of the dash-

board material and bend them.

• Fastening the unit to the factory

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Dashboard

182

Rubber bush

Screw

Conceal tape

Holder

Side bracket

Screw (2 × 3 mm)

Fig. 15

• After installing the unit into the dash-

board, reattach the frame.

Fig. 16

radio mounting bracket. (Fig. 17)

(Fig. 18) (Fig. 19)

Dashboard or

Select a position where the screw holes

Console

Factory radio mounting

of the bracket and the screw holes of

bracket

this product become aligned (are fitted),

and tighten the screws at 2 places on

each side. Use any of binding screws (4

× 3 mm), binding screws (5 × 6 mm) or

flush surface screws (5 × 6 mm),

Fixing the front panel

depending on the shape of the screw

If you do not operate the removing and

holes in the bracket.

*1 Use binding screws (4 × 3 mm) only.

attaching the front panel function, use

the supplied fixing screws to fix the

front panel to this unit.

• Fix the front panel to the unit

using fixing screws after remov-

* 1

ing the front panel. (Fig. 20)

* 1

Fig. 17

• When installing in a shallow space,

use the following screw holes. In this

case, stick conceal tape on parts that

protrude from the dashboard.

Fixing screw

Conceal tape

* 1

Fig. 18

Screw

Fig. 19

Fig. 20