Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player Kurulum Kılavuzu - Sayfa 4
Araç Alıcısı Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player 8 sayfaları. Owner's manual
Ayrıca Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player için: Manuel (39 sayfalar), Kullanıcı El Kitabı (34 sayfalar)
Sayfayı Yazdır
Installation
When connecting the external video component and the display
Audio input
Video input
External
video
component
(sold separately)
To audio outputs
Audio output
RCA cables
Multi-DVD Player
(sold separately)
(sold separately)
To video output
Video output
Video output
RCA cable
Display with
(sold separately)
RCA input jacks
To video input
• It is necessary to set AV INPUT to VIDEO in SET UP when connecting the external
video component.
• It is necessary to set AV INPUT to M-DVD in SET UP when connecting a multi-DVD
player.
When using a display connected to rear video output
This product's rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
WARNING:
• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while
Driving.
Note:
DIN Front/Rear-mount
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
This unit can be properly installed
up properly, and the unit and the system work
either from "Front" (conventional DIN
properly.
Front-mount) or "Rear" (DIN Rear-
• Use only the parts included with the unit to ensure
mount installation, utilizing threaded
proper installation. The use of unauthorized parts
screw holes at the sides of unit chassis).
can cause malfunctions.
For details, refer to the following illus-
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
trated installation methods.
of the vehicle.
• Install the unit where it does not get in the driver's
Before installing the unit
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• Remove the frame and the hold-
• Do not install the display where it may (i) obstruct
er. (Fig. 14)
the driver's vision, (ii) impair the performance of
any of the vehicle's operating systems or safety
Pull out to remove the frame and then
features, including air bags, hazard lamp buttons or
loosen the screws (2 × 3 mm) to
(iii) impair the driver's ability to safely operate the
remove the holder. (When reattaching
vehicle.
the frame, point the side with a groove
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot
downwards and attach it.)
— for instance, near a heater outlet.
• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 12)
Fig. 11
30°
Fig. 12
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
fires to radiate freely. (Fig. 13)
Do not close this area.
Fig. 13
DIN Front-mount
Installation with the rubber bush
1. Decide the position of the side
brackets. (Fig. 15)
When installing in a shallow space,
change the position of side brackets. In
this case, stick conceal tape on parts
that protrude from the dashboard.
Side bracket
Flush surface screw (5 × 6 mm)
Holder
Screw (2 × 3 mm)
Frame
Fig. 14
2. Install the unit into the dash-
DIN Rear-mount
board. (Fig. 16)
After inserting the holder into the dash-
Installation using the screw holes on
board, then select the appropriate tabs
the side of the unit
according to the thickness of the dash-
board material and bend them.
• Fastening the unit to the factory
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
Dashboard
182
Rubber bush
53
Screw
Conceal tape
Holder
Side bracket
Screw (2 × 3 mm)
Fig. 15
• After installing the unit into the dash-
board, reattach the frame.
Fig. 16
<ENGLISH>
radio mounting bracket. (Fig. 17)
(Fig. 18) (Fig. 19)
Dashboard or
Select a position where the screw holes
Console
Factory radio mounting
of the bracket and the screw holes of
bracket
this product become aligned (are fitted),
and tighten the screws at 2 places on
each side. Use any of binding screws (4
× 3 mm), binding screws (5 × 6 mm) or
flush surface screws (5 × 6 mm),
Fixing the front panel
depending on the shape of the screw
If you do not operate the removing and
holes in the bracket.
*1 Use binding screws (4 × 3 mm) only.
attaching the front panel function, use
the supplied fixing screws to fix the
front panel to this unit.
• Fix the front panel to the unit
using fixing screws after remov-
* 1
ing the front panel. (Fig. 20)
* 1
Fig. 17
• When installing in a shallow space,
use the following screw holes. In this
case, stick conceal tape on parts that
protrude from the dashboard.
Fixing screw
Conceal tape
* 1
* 1
Fig. 18
Screw
Fig. 19
Fig. 20