Pioneer DC-Z85 Manuel d'utilisation - Page 9

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Pioneer DC-Z85. Pioneer DC-Z85 28 pages. Stereo double cassette deck amplifier / fm/am digital synthesizer tuner / stereo turntable

Imprimer la page

PANEL FACILITIES

@ Display section

Shows current time, received frequency, contents of timer settings,

etc.

leat

—

ee: A Utes 9 fae

Gas

® MONDO indicator

Lights when the MPX button is set to ON. When this indicator is lit,

FM stereo broadcasts are reproduced monauraily.

® TUNED indicator

Lights when a broadcast is received and tuned in well.

Lights when an FM stereo broadcast is received (MPX button set to

OFF).

Lights when the LOCAL button is set to ON.

These show various timer setting.

Indicates that the sleep timer is activated.

i® Frequency display

Shows received broadcast frequency. Also gives scrolling display of

main function status.

FM and MHz light: FM reception.

AM and kHz light: AM reception.

@ Time display

This shows the present time and during recording, it shows the

elapsed recording time. When you listen to a broadcast, the STATION

CALL number is displayed.

@® Deck li REC TIME indicator

Lights when deck If is recording.

NOTE:

The elapsed recording time might

not be displayed due to noise from

the power supply caused by improper timing when connecting the

power cord. In such case, disconnect the power card and connect it

again.

@ STATION CALL buttons

Used for memorizing and recalling memorized stations.

® SET buttons

Used for current time, timer playback, and timer recording setting.

@ Timer seiector buttons

[WAKE-UP 1,2]

Used for timer playback setting.

[REC]

Used for timer recording setting.

® CLOCK ADJ button

Used for starting the clock adjustment.

@® TUNING/TIMER (~, +) buttons

[During tuning]

Used for locating stations.

Use "—" button for lower, and "+" button for higher frequencies.

[During time and timer setting]

Used for adjusting the clock, timer settings and its related adjust-

ments.

@® LOCAL button

Use this if the broadcast signal is too strong, causing noise and dis-

tortion. The atttenuator reduces the strength of the signal, reducing

noise and distortion.

@® MPX (FM MONO} button

Turn on when there is much noise during reception of FM stereo

broadcasts. The reproduced sound will become monaural but noise

will be reduced.

Used for memorizing stations. When the button is pressed, the fre-

quency display will flash. To memorize the frequency of any station,

press a station call button while the frequency display flashes

@ BAND selector button

Each time this button is pressed, FM or AM reception is selected al-

ternately.

@ CHECK button

Used for confirming timer settings, after setting for timer playback

or timer recording.

4) SLEEP button

Sats the sleep timer

Each time you press this button, the setting changes as shown hera.

The current setting is shown on the tuner display.

Power turns off when your set time has elapsed.

p——

90 ——

60 ———————--

(Approx. 90

(Approx. 60

(Approx. 30

minutes)

——-——-— (AUTO)

OFF ————

If you press the SLEEP button during recording, AUTO is displayed,

and power is switched off at the end of recording.

[ Cassette deck amplifier: D

@ This unit has an automatic

tape type

* Tapes can be played back on deck |; tapes can be played back

and recorded on deck Il.

ler.

¢ Use a normal or chrome position tape.

@ Amplifier section

@) POWER STANDBY/ON switch /STANDBY indicator

This is the switch for electric power

ON:

When set to the ON position, power is supplied and

the unit becomes operational.

STANDBY:

When set to the STANDBY position, the main

power

flow is cut and the unit is no longer fully operational

A minute flow of power feeds the unit to maintain

operation readinss.

When

the STANDBY

indicator is on, the unit is in

STANDBY.