Pioneer DC-Z85 Operating Instructions Manual - Page 9
Browse online or download pdf Operating Instructions Manual for Amplifier Pioneer DC-Z85. Pioneer DC-Z85 28 pages. Stereo double cassette deck amplifier / fm/am digital synthesizer tuner / stereo turntable
Print Page
PANEL FACILITIES
@ Display section
Shows current time, received frequency, contents of timer settings,
etc.
a
leat
=
a
a
=)
—
ae
7
ee: A Utes 9 fae
Gas
=
6
oy
6
® MONDO indicator
Lights when the MPX button is set to ON. When this indicator is lit,
FM stereo broadcasts are reproduced monauraily.
® TUNED indicator
Lights when a broadcast is received and tuned in well.
© STEREO indicator
Lights when an FM stereo broadcast is received (MPX button set to
OFF).
© LOCAL indicator
Lights when the LOCAL button is set to ON.
© Timer indicators
These show various timer setting.
© SLEEP indicator
Indicates that the sleep timer is activated.
i® Frequency display
Shows received broadcast frequency. Also gives scrolling display of
main function status.
FM and MHz light: FM reception.
AM and kHz light: AM reception.
@ Time display
This shows the present time and during recording, it shows the
elapsed recording time. When you listen to a broadcast, the STATION
CALL number is displayed.
@® Deck li REC TIME indicator
Lights when deck If is recording.
NOTE:
The elapsed recording time might
not be displayed due to noise from
the power supply caused by improper timing when connecting the
power cord. In such case, disconnect the power card and connect it
again.
ry
@ STATION CALL buttons
Used for memorizing and recalling memorized stations.
® SET buttons
Used for current time, timer playback, and timer recording setting.
@ Timer seiector buttons
[WAKE-UP 1,2]
Used for timer playback setting.
[REC]
Used for timer recording setting.
® CLOCK ADJ button
Used for starting the clock adjustment.
@® TUNING/TIMER (~, +) buttons
[During tuning]
Used for locating stations.
Use "—" button for lower, and "+" button for higher frequencies.
[During time and timer setting]
Used for adjusting the clock, timer settings and its related adjust-
ments.
@® LOCAL button
Use this if the broadcast signal is too strong, causing noise and dis-
tortion. The atttenuator reduces the strength of the signal, reducing
noise and distortion.
@® MPX (FM MONO} button
Turn on when there is much noise during reception of FM stereo
broadcasts. The reproduced sound will become monaural but noise
will be reduced.
© MEMORY button
Used for memorizing stations. When the button is pressed, the fre-
quency display will flash. To memorize the frequency of any station,
press a station call button while the frequency display flashes
@ BAND selector button
Each time this button is pressed, FM or AM reception is selected al-
ternately.
@ CHECK button
Used for confirming timer settings, after setting for timer playback
or timer recording.
4) SLEEP button
Sats the sleep timer
Each time you press this button, the setting changes as shown hera.
The current setting is shown on the tuner display.
Power turns off when your set time has elapsed.
p——
90 ——
60 ———————--
30
(Approx. 90
(Approx. 60
(Approx. 30
minutes)
minutes)
minutes)
——-——-— (AUTO)
=
OFF ————
If you press the SLEEP button during recording, AUTO is displayed,
and power is switched off at the end of recording.
[ Cassette deck amplifier: D
@ This unit has an automatic
tape type
* Tapes can be played back on deck |; tapes can be played back
and recorded on deck Il.
© Sound can be recorded as adjusted by the soundimage control
|
ler.
¢ Use a normal or chrome position tape.
@ Amplifier section
@) POWER STANDBY/ON switch /STANDBY indicator
This is the switch for electric power
ON:
When set to the ON position, power is supplied and
the unit becomes operational.
STANDBY:
When set to the STANDBY position, the main
power
flow is cut and the unit is no longer fully operational
A minute flow of power feeds the unit to maintain
operation readinss.
When
the STANDBY
indicator is on, the unit is in
STANDBY.