Whirlpool AWM 6145/3 Manuel de démarrage rapide - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} Whirlpool AWM 6145/3. Whirlpool AWM 6145/3 3 pages.
Imprimer la page
CONSUMPTION DATA
Temperature
Selector
Programme
(°C)
Cotton
95
Cotton
60
Cotton
40
Synthetics
60
Synthetics
40
Daily
40
Short
30
Delicates
40
Wool
30
Handwash
30
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the
household conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE
PROGRAMME
Add the detergent as described in the programme
table or in the chapter "Detergents and Additives"
in the booklet.
1. Turn the programme selector knob to the
desired programme and temperature.
2. The remaining time display shows the duration of
the chosen programme (in hours and minutes)
and after taking some seconds for calculating,
the pilot lamp of the "Start/Pause" button is
flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
SELECT ANY DESIRED OPTION
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the
indication lights switch off automatically.
Unsuitable combinations of options are
deselected automatically.
Load
Water
Energy
(kg)
(l)
(kWh)
(hours : minutes)*
5.5
54**
1.90
5.5
49
1.04
5.0
44
0.60
2.5
55
0.80
2.5
55
0.60
3.0
45
0.50
3.0
37
0.40
1.5
60
0.60
1.0
60
0.30
1.0
45
0.30
"Easy Ironing" button
• Can be used together with Cotton, Synthetics and
Daily programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
"Eco Wash" button
• The duration of the wash is extended and the
temperature reduced to save up to 40% of energy
but maintaining good washing results.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
"Intensive Rinse" button
• More water and a longer time in rinse cycle is
added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
"Rinse Hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
Approx.
avoid creasing and prevent colours from
Programme
Duration
changing.
• This option is particularly recommended for the
programme "Synthetics", "Daily" and
2:05
"Delicates".
2:25
• This function is particularly useful if you want
2:10
to postpone spinning to a later time, or if you
1:35
want to drain only.
1:25
Note: The programme stops to "Rinse Hold" at the
1:00
time the "Rinse Hold" light in the programme flow
0:35
indication is on.
0:50
Terminate the "Rinse Hold" option:
0:45
• Press the "Rinse Hold" button again; the
programme will terminate automatically with
0:45
the final spin cycle for the present wash
programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain"
programme and press the "Start/Pause" button
again when flashing.
"Variable Spin" button
• Every programme has an automatic predefined
maximum spin speed.
• Press the button to set another spin speed.
• If the spin speed "0" is selected, the final
spinning is cancelled but intermediate spin
peaks remain during rinse. The water is drained
out only.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The pilot lamp of the "Start/Pause" button lights up.
The indicator lamps show the sequence reached in
the programme. After starting the programme, the
sequence indication runs from left to right through
Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding lamp goes out.
DOOR LOCK
The door can be opened when the "Door Open"
indication is on.
PROGRAMME END
• The remaining time is on "0:00" and all the
lights of the programme sequence indication
are off.
"
1. Turn the programme selector to the
position.
2. Turn the water supply tap off.
3. Open the door and unload the machine.
4. Close the tap and leave the door ajar to allow
the drum to dry out.
CHANGE THE PROGRAMME, OPTIONS AFTER
PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button again. The
new programme continues at the same position
where the previous programme was
interrupted. Do not add detergent for this
programme.
CANCEL A PROGRAMME BEFORE THE END
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Set the programme selector to "Drain". The
spin indicators show "0" and the remaining
time shows "0:02".
3. Press the "Start/Pause" button to start the
drain programme.
Whirlpool is a registered trademark of Whirlpool USA.
5019 301 05442
"