Directed Electronics 1100X/F-FM Manuel de démarrage rapide

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} Directed Electronics 1100X/F-FM. Directed Electronics 1100X/F-FM 2 pages.

Directed Electronics 1100X/F-FM Manuel de démarrage rapide
note to the installer:
THIS GUIDE IS INTENDED FOR USE WITH AN 1100F OR 1100X THAT HAS BEEN UPDATED TO AN 1100FM USING THE DIRECTLINK UPDATER TOOL.
DIRECTLINK UPDATER SOFTWARE IS AVAILABLE AT WWW.DIRECTECHS.COM.
WarninG! READ MANUAL PRIOR TO INSTALLATION
proDUct Description
The 1100X/F-FM interface module is used when installing remote start products in
Ford/Mazda vehicles equipped with a factory immobilizer. The 1100X/F-FM allows
for easy interfacing between the remote start and the factory immobilizer, while
maintaining the integrity of the OEM system. The factory transponder-based anti-
theft system uses a small electronic chip hidden in the key to send a code to the
vehicle's transceiver when the ignition is energized. The key must be placed in the
ignition and turned to the RUN position. This energizes a coil surrounding the key,
which in turn energizes the chip, which sends a code to the vehicle. If the vehicle
does not detect the code being sent, the vehicle will start and then immediately
shut off or will just crank, and the anti-theft light will fl ash. The 1100X/F-FM pro-
vides a valid code to the vehicle whenever it is remote started, but does not affect
the immobilizer system during normal vehicle operation; the immobilizer system
remains fully functional.
step 1: select installation moDe
Complete the wire connections to the vehicle and to the remote starter/alarm
system. Connect all harnesses including the 4-pin power harness. The module
LED will now fl ash green intermittently. (Note: if this condition is not present, your
module may need to be reset to the factory default).
1. Press and release the programming switch to select installation
mode.
Press the switch to alternate between the two modes (only standard
mode should be used).
1 fl ash, pause, I fl ash, pause = (This mode is not used)
fl ashes, pause, fl ashes, pause = Standard installation mode
. Once your installation mode is selected, press and hold the
programming button until the LED displays a solid green light for two
seconds. Your installation mode is now programmed. Please proceed
to step .
NOTE: Should you wish to change the installation mode, follow the
"Factory Reset" instructions.
step 2: Determine transponDer type
Refer to the transponder cross reference chart to determine transponder type and
programming procedure.
notice:
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the
vehicle itself or to the installed device. This device must be installed by a certifi ed technician. This guide has been written for properly trained technicians; a certain level
of skill and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
© 2006 Directed Electronics, All rights reserved.
proGramminG instrUctions
1. If the transponder type is 1, proceed to A.
. If the transponder type is either or 3, proceed to B
A: Transponder Type 1
1. Insert the vehicle key into the ignition.
. Turn ignition to the "ON" position and wait for the LED to illuminate green for
3. Programming is complete.
B: Transponder Type or Type 3
IMPORTANT: Both keys are required to complete the programming procedure.
A maximum 5 second delay between each step is permitted. If the delay is
exceeded, the vehicle will not allow programming to continue. The programming
procedure must be restarted.
1. Insert the 1st key into the ignition. Turn ignition to the "ON" position, the LED
. Insert the nd key into the ignition. Turn ignition to the "ON" position and
3. Press and release the programming button once and start the vehicle through
leD DiaGnostics
1. During STEP , if the LED fl ashes red this indicates the wire connections are incorrect.
. Once programming has been completed, if the LED fl ashes red the module
3. When the remote starter is engaged, the led will fl ash green to indicate the
If the LED remains illuminated red, the device is incorrectly programmed.
factory reset
1. Unplug all connectors from the module.
. Press and hold the programming button while inserting the 4-PIN
3. The LED will begin to fl ash red. Immediately release the programming button.
4. Plug remaining connectors and return to: STEP 1: SELECT INSTALLATION
WirinG DiaGram
Programming Button
LED
BLUE/RED (NC)
BLUE/YELLOW (NC)
GREEN/RED - ECM-RX
GREEN/YELLOW (NC)
GRAY/RED - ECM-TX
GRAY/YELLOW (NC)
ORANGE (NC)
PINK/BLACK (NC)
PINK - IGNITION INPUT
RED - 12V
BLACK - GROUND
NO WIRE (NC)
BLUE/WHITE - STATUS OUTPUT
1
two seconds.
will illuminate green. Wait for the car security light to turn off, turn ignition to
the "OFF" position and remove the key.
wait for the car security light to turn off. Turn ignition to the OFF" position and
remove the key.
use of the remote controlled starter OR "jump" ignition. Wait for LED to illumi-
nate green for two seconds. Programming is complete.
failed to learn correctly. Reset module and repeat the programming procedure.
current transponder mode as follows:
1 x green fl ash = PATS 1 x green fl ashes = PATS 3 x green fl ashes = PATS 3
standard connector.
The LED will turn on solid for seconds to confi rm module reset.
MODE.
KEY
REMOTE
STARTER
1100
X/f-fm
transponder bypass
forD/maZDa
TYPE 1 & INSTALLS
N1100X/F-FM 11-06