Directed Electronics 1100X/F-FM Quick Start Manual

Browse online or download pdf Quick Start Manual for Automobile Accessories Directed Electronics 1100X/F-FM. Directed Electronics 1100X/F-FM 2 pages.

Print Page

Directed Electronics 1100X/F-FM Quick Start Manual

note to the installer:

THIS GUIDE IS INTENDED FOR USE WITH AN 1100F OR 1100X THAT HAS BEEN UPDATED TO AN 1100FM USING THE DIRECTLINK UPDATER TOOL.

DIRECTLINK UPDATER SOFTWARE IS AVAILABLE AT WWW.DIRECTECHS.COM.

WarninG! READ MANUAL PRIOR TO INSTALLATION

proDUct Description

The 1100X/F-FM interface module is used when installing remote start products in

Ford/Mazda vehicles equipped with a factory immobilizer. The 1100X/F-FM allows

for easy interfacing between the remote start and the factory immobilizer, while

maintaining the integrity of the OEM system. The factory transponder-based anti-

theft system uses a small electronic chip hidden in the key to send a code to the

vehicle's transceiver when the ignition is energized. The key must be placed in the

ignition and turned to the RUN position. This energizes a coil surrounding the key,

which in turn energizes the chip, which sends a code to the vehicle. If the vehicle

does not detect the code being sent, the vehicle will start and then immediately

shut off or will just crank, and the anti-theft light will ﬂ ash. The 1100X/F-FM pro-

vides a valid code to the vehicle whenever it is remote started, but does not affect

the immobilizer system during normal vehicle operation; the immobilizer system

remains fully functional.

step 1: select installation moDe

Complete the wire connections to the vehicle and to the remote starter/alarm

system. Connect all harnesses including the 4-pin power harness. The module

LED will now ﬂ ash green intermittently. (Note: if this condition is not present, your

module may need to be reset to the factory default).

1. Press and release the programming switch to select installation

mode.

Press the switch to alternate between the two modes (only standard

mode should be used).

1 ﬂ ash, pause, I ﬂ ash, pause = (This mode is not used)

ﬂ ashes, pause, ﬂ ashes, pause = Standard installation mode

. Once your installation mode is selected, press and hold the

programming button until the LED displays a solid green light for two

seconds. Your installation mode is now programmed. Please proceed

to step .

NOTE: Should you wish to change the installation mode, follow the

"Factory Reset" instructions.

step 2: Determine transponDer type

Refer to the transponder cross reference chart to determine transponder type and

programming procedure.

notice:

The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the

vehicle itself or to the installed device. This device must be installed by a certiﬁ ed technician. This guide has been written for properly trained technicians; a certain level

of skill and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.

proGramminG instrUctions

1. If the transponder type is 1, proceed to A.

. If the transponder type is either or 3, proceed to B

A: Transponder Type 1

1. Insert the vehicle key into the ignition.

. Turn ignition to the "ON" position and wait for the LED to illuminate green for

3. Programming is complete.

B: Transponder Type or Type 3

IMPORTANT: Both keys are required to complete the programming procedure.

A maximum 5 second delay between each step is permitted. If the delay is

exceeded, the vehicle will not allow programming to continue. The programming

procedure must be restarted.

1. Insert the 1st key into the ignition. Turn ignition to the "ON" position, the LED

. Insert the nd key into the ignition. Turn ignition to the "ON" position and

3. Press and release the programming button once and start the vehicle through

leD DiaGnostics

1. During STEP , if the LED ﬂ ashes red this indicates the wire connections are incorrect.

. Once programming has been completed, if the LED ﬂ ashes red the module

3. When the remote starter is engaged, the led will ﬂ ash green to indicate the

If the LED remains illuminated red, the device is incorrectly programmed.

factory reset

1. Unplug all connectors from the module.

. Press and hold the programming button while inserting the 4-PIN

3. The LED will begin to ﬂ ash red. Immediately release the programming button.

4. Plug remaining connectors and return to: STEP 1: SELECT INSTALLATION

WirinG DiaGram

Programming Button

LED

BLUE/RED (NC)

BLUE/YELLOW (NC)

GREEN/RED - ECM-RX

GREEN/YELLOW (NC)

GRAY/RED - ECM-TX

GRAY/YELLOW (NC)

ORANGE (NC)

PINK/BLACK (NC)

PINK - IGNITION INPUT

RED - 12V

BLACK - GROUND

NO WIRE (NC)

BLUE/WHITE - STATUS OUTPUT

two seconds.

will illuminate green. Wait for the car security light to turn off, turn ignition to

the "OFF" position and remove the key.

wait for the car security light to turn off. Turn ignition to the OFF" position and

remove the key.

use of the remote controlled starter OR "jump" ignition. Wait for LED to illumi-

nate green for two seconds. Programming is complete.

failed to learn correctly. Reset module and repeat the programming procedure.

current transponder mode as follows:

1 x green ﬂ ash = PATS 1 x green ﬂ ashes = PATS 3 x green ﬂ ashes = PATS 3

standard connector.

The LED will turn on solid for seconds to conﬁ rm module reset.

MODE.

KEY

REMOTE

STARTER

1100

X/f-fm

transponder bypass

forD/maZDa

TYPE 1 & INSTALLS

N1100X/F-FM 11-06