Camlogic PFG-06/TC Installation et maintenance - Page 2

Parcourez en ligne ou téléchargez le pdf Installation et maintenance pour {nom_de_la_catégorie} Camlogic PFG-06/TC. Camlogic PFG-06/TC 2 pages. Capacitive level gauges

Imprimer la page

ELECTRICAL WIRING

Diameters of 0.5 mm² to 1.5 mm² are sufficient for the connecting cables owing to the low current values applied.

In any case the section must prevent the current density from exceeding 4 A/mm² in each conductor. The cross-section

of the conductors must also be adequate in relation to the lenght of the cable used to avoid a drop in the voltage

along the cable over the values prescribed by the regulations on the subject.

One of the conductors is solely used for the earthing of the capacitive

level gauge PFG-06. It is likewise recommended to use flexible cables with

an adequate outside diameter for the cable entries used (not supplied)

to ensure a perfect seal of the cable clamp on the power supply and

signal carrying cable.

Use exclusively cable entries certified according to the directive 2014/34/EU

Category 2 and EN 60079-31.

CAUTION :

In the terminal board compartment, the connection for

Faston type cable terminal whose position is marked by the symbol

on the printed circuit (Fig. 1) is used for the earthing of the level gauge.

The yellow-green conductor (only green for the USA) of the power cable

must be connected to this terminal.

The ground connection of the level gauge, through the yellow-green

conductor, is compulsory.

The external earthing has to be carried out by the installator.

The equipment has to be protected against impact and electrostatic

inside the silo.

The user has to protect the equipment circuits with fuses against short

circuit.

- The max. surface temperature considered is without dust and not safety

distance.

Inside the cover there is the wiring plate (Fig. 2) which has printed on it the wiring diagram for the power supply and

use of the level gauge.

ø102

ø28

PFG-06

ø88

ø102

ø28

PFG-06/TC

ø88

The manufacturer CAMLogic declares under its own responsability that the product PFG-06/. answers to the requisites

of the European Directive 2014/34/EU in consideration of the standards: EN IEC 60079-0:2018, EN 60079-31:2014.

Marking:

II 1/2D Ex ta/tb IIIC T90°C IP65 Da/Db - The permitted ambient temperature range from -20 to +70 °C.

Notified corporate body that releases the examination TÜV ITALIA. Certificate number TÜV IT 13 ATEX 071.

Corporate body entrusted of the periodic overseeing TÜV ITALIA.

Instructions Manual No. 01701 25.12 - Rev. 01

no part of it may be disclosed without written authorization from CAMLogic.

This manual, even after the sale of the level gauge, is lent and remains the property of the Manufacturer.

SGC2012

REFERENCE FIGURES

SW 52

ø32

INTERVENTION

DISTANCE 0-25 mm.

ø38.1

ø50.4

DECLARATION OF CONFORMITY

Always check that the mains voltage and

frequency correspond to those given on the

plate of the level gauge before powering it.

The power cable must be fixed to the main by

a qualified installer in compliance with the

current safety standards in merit.

For electric connections to the terminal use

Faston cable terminals ( 6.3 x 0.8 mm. ).

MAINTENANCE

Capacitive level gauge PFG-06 needs no routine

ø1"1/2 Gas

maintenance.

WARRANTY

CAMLogic, in addition to the terms of the supply

Sensor area

contract, guarantees its products for a period

of twenty-four (24) months from the date of

shipment.

This warranty is expressed only in the repair

or replacement free of charge of parts that,

after careful examination by the Manufacturer,

turn out to be defective.

Warranty, excluding all liability for direct or

ø32

indirect damage, is considered to be restricted

to only defects in materials and has no effect

PFG-06/F

if the parts returned turn out to have been

anyhow dismantled, tampered with or repaired

by anyone other than the Manufacturer.

Warranty likewise excludes damage deriving from

negligence, carelessness, bad or improper use

of the level gauge, or from bad handling by the

operator and faulty installation.

Moreover, warranty is forfeit if non-genuine spare

ø120

parts have been used.

A returned level gauge, even if under warranty,

ø140

must be shipped carriage free.

All the informations contained in this manual are confidential and

Fig.3

01701 25.12 - Rev. 01