Alton DW18903PR-6H Manuel d'instruction - Page 9
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Alton DW18903PR-6H. Alton DW18903PR-6H 12 pages. 6gallon (23 l) portable wet/dry vacuum
English
4. Lower top handle
1
on vacuum to lay at on top
of housing. This will secure unit in bracket.
Detach Vac:
1. Push release lever on bracket with thumb, while
moving top handle on vacuum to the up position.
2. Grasp top handle with one hand and place other
hand under front of tank.
3. Pull upward until vacuum detaches from bracket.
Resetting the Remote Control (Fig. G)
1.Set the power switch on the vacuum to the remote
control option"II".
2.Make sure the distance between the remote control
and the vacuum cleaner for less than 0.5m, press and
hold the paring button
of the remote control for more
than 3 seconds and the LED will ash , the inside motor
makes a sound to indicate a successful pairing.
To Unpair with the Remote Control (Fig. G)
Make sure the distance between the remote control
and the vacuum cleaner for less than 0.5m, press and
hold the paring button
of the remote control for more
than 3 seconds and the LED will ash , the inside motor
makes a sound to indicate the pairing is invalid.
Empty the Tank (Fig. K)
WARNING:
To reduce the risk of injury from
accidental starting, unplug power cord before emptying
the dust tank.
1. Remove the power head assembly of the wet/dry
vac bypulling outward on the lid clips located on each
side of the vac. Lift off the power head assembly.
2. Dump the tank contents into the proper waste
disposal container.
Blowing Operation
WARNING:
To avoid injury to bystanders, keep
them clear of blowing debris.
CAUTION:
Wear a dust mask if blowing creates
dust which might be inhaled.
CAUTION:
To reduce the risk of hearing loss, wear
ear protectors when using the vac/blower for extended
hours or when using it in a noisy area.
Blowing Feature (Fig. C)
Your vac contains a blowing feature. It has the
capability to blow sawdust and other debris. It can
be used to blow dust and debris out of garages or off
patios and driveways. Follow the steps below to use
your vac as a blower.
1. Locate blowing port on your vac.
2. Insert one end of the 1-7/8'' x 5' to 20' exible hose
into the blowing port.
3. Turn vacuum "ON".
Storage (Fig. A / F)
Store the power cord
5
bottom accessory box/cord wrap
may be wrapped around the wall bracket and the
accessories stored in the tool box
readily available. Never allow liquids to sit in the tank
for any extended period of time. The vacuum should
be stored indoors.
wrapping it around the
. The hose
8
so they can be
21
Optional Accessories
WARNING:
Since accessories, other than those
offered by ALTON, have not been tested with this
product, use of such accessories with this appliance
could be hazardous.
To reduce the risk of injury, only ALTON recommended
accessories should be used with this product.
CLEANING
To keep your wet/dry vac looking its best, clean the
outside with a cloth dampened with warm water and
mild soap.
To clean the tank:
20
1. Dump out debris.
2. Wash tank thoroughly with warm water and mild soap.
3. Wipe out with dry cloth.
TROUBLESHOOTING
WARNING:
TO REDUCE THE RISK OF INJURY FROM
20
MOVING PARTS AND/OR ELECTRICAL SHOCK,
TURN POWER SWITCH OFF AND DISCONNECT
GROUNDED PLUG FROM ELECTRICAL OUTLET
BEFORE PERFORMING TROUBLESHOOTING
CHECKS.
Minor problems often can be xed without calling
customer service.
PROBLEM
Motor does not run
Suction capacity
decreases
Vacuum stops
running
Dust comes out
while vacuuming
WARNING:
If the power cord is damaged, it must
be replaced by the manufacturer, its service agent or
similarly quali ed persons in order to avoid a hazard.
7
SOLUTION
Check power cord, plugs and outlet.
Ensure the on/off switch is in the
ON position ( I )
Remove blockages in the suction
nozzle, suction tube, suction hose
or lters.
Replace the paper or eece bag.
Check for proper installation of the
lters.
Clean or replace the lters.
Empty
Empty canister, refer to
the tank
Operating.
under
instructions
Thermal overload has been tripped:
1. Turn the vacuum off and
disconnect vacuum cleaner from
power source.
2. Empty the canister, if needed.
3. Allow the unit to cool.
4. Plug the power cord into an
appropriate outlet and turn on/off
switch to the ON position ( I ) to
test.
Check for proper installation of the
lters.
Ensure lters are not damaged;
replace if necessary.
Ensure lter seals are in place and
are secure.