Alton DW18903PR-6H 사용 설명서 - 페이지 9

{카테고리_이름} Alton DW18903PR-6H에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Alton DW18903PR-6H 12 페이지. 6gallon (23 l) portable wet/dry vacuum

페이지 인쇄

English

4. Lower top handle

on vacuum to lay at on top

of housing. This will secure unit in bracket.

Detach Vac:

1. Push release lever on bracket with thumb, while

moving top handle on vacuum to the up position.

2. Grasp top handle with one hand and place other

hand under front of tank.

3. Pull upward until vacuum detaches from bracket.

Resetting the Remote Control (Fig. G)

1.Set the power switch on the vacuum to the remote

control option"II".

2.Make sure the distance between the remote control

and the vacuum cleaner for less than 0.5m, press and

hold the paring button

of the remote control for more

than 3 seconds and the LED will ash , the inside motor

makes a sound to indicate a successful pairing.

To Unpair with the Remote Control (Fig. G)

Make sure the distance between the remote control

and the vacuum cleaner for less than 0.5m, press and

hold the paring button

of the remote control for more

than 3 seconds and the LED will ash , the inside motor

makes a sound to indicate the pairing is invalid.

Empty the Tank (Fig. K)

WARNING:

To reduce the risk of injury from

accidental starting, unplug power cord before emptying

the dust tank.

1. Remove the power head assembly of the wet/dry

vac bypulling outward on the lid clips located on each

side of the vac. Lift off the power head assembly.

2. Dump the tank contents into the proper waste

disposal container.

Blowing Operation

WARNING:

To avoid injury to bystanders, keep

them clear of blowing debris.

CAUTION:

Wear a dust mask if blowing creates

dust which might be inhaled.

CAUTION:

To reduce the risk of hearing loss, wear

ear protectors when using the vac/blower for extended

hours or when using it in a noisy area.

Blowing Feature (Fig. C)

Your vac contains a blowing feature. It has the

capability to blow sawdust and other debris. It can

be used to blow dust and debris out of garages or off

patios and driveways. Follow the steps below to use

your vac as a blower.

1. Locate blowing port on your vac.

2. Insert one end of the 1-7/8'' x 5' to 20' exible hose

into the blowing port.

3. Turn vacuum "ON".

Storage (Fig. A / F)

Store the power cord

bottom accessory box/cord wrap

may be wrapped around the wall bracket and the

accessories stored in the tool box

readily available. Never allow liquids to sit in the tank

for any extended period of time. The vacuum should

be stored indoors.

wrapping it around the

. The hose

so they can be

Optional Accessories

WARNING:

Since accessories, other than those

offered by ALTON, have not been tested with this

product, use of such accessories with this appliance

could be hazardous.

To reduce the risk of injury, only ALTON recommended

accessories should be used with this product.

CLEANING

To keep your wet/dry vac looking its best, clean the

outside with a cloth dampened with warm water and

mild soap.

To clean the tank:

1. Dump out debris.

2. Wash tank thoroughly with warm water and mild soap.

3. Wipe out with dry cloth.

TROUBLESHOOTING

WARNING:

TO REDUCE THE RISK OF INJURY FROM

MOVING PARTS AND/OR ELECTRICAL SHOCK,

TURN POWER SWITCH OFF AND DISCONNECT

GROUNDED PLUG FROM ELECTRICAL OUTLET

BEFORE PERFORMING TROUBLESHOOTING

CHECKS.

Minor problems often can be xed without calling

customer service.

PROBLEM

Motor does not run

Suction capacity

decreases

Vacuum stops

running

Dust comes out

while vacuuming

WARNING:

If the power cord is damaged, it must

be replaced by the manufacturer, its service agent or

similarly quali ed persons in order to avoid a hazard.

SOLUTION

Check power cord, plugs and outlet.

Ensure the on/off switch is in the

ON position ( I )

Remove blockages in the suction

nozzle, suction tube, suction hose

or lters.

Replace the paper or eece bag.

Check for proper installation of the

lters.

Clean or replace the lters.

Empty

Empty canister, refer to

the tank

Operating.

under

instructions

Thermal overload has been tripped:

1. Turn the vacuum off and

disconnect vacuum cleaner from

power source.

2. Empty the canister, if needed.

3. Allow the unit to cool.

4. Plug the power cord into an

appropriate outlet and turn on/off

switch to the ON position ( I ) to

test.

Check for proper installation of the

lters.

Ensure lters are not damaged;

replace if necessary.

Ensure lter seals are in place and

are secure.