Ambirad AMBITEC PLUS Manual - Halaman 6

Jelajahi secara online atau unduh pdf Manual untuk Panel Kontrol Ambirad AMBITEC PLUS. Ambirad AMBITEC PLUS 11 halaman. Energy saving electronic control panel

Halaman Cetak

AMBITEC

ARE

SERIES

Adjust heat < > vent differential (8)

Press the

to set the desired

temperature differential (dead band)

between heat and vent when in the Auto

mode.

Adjust GM 44 differential (9)

Press the

to set the number of degrees

that the 0 - 5VDC proportional band is to

vary over.

Adjust AmbiTec Plus type (10)

Press the

to set the control panel to

the type of unit required. If the control

panel is to be used to control an individual

heater then set the display to read, 'Adjust

Energy mizor 00' . If more than one control

panel is to be used to control the heaters in

a Master/Slave configuration the use the

to set the unit to be designated as the

Master to read 'Adjust Master 00' . If a unit

is to be designated as a slave panel then use

the

to set each slave to read 'Adjust

Slave XX' . XX is to be interpreted to be any

number from 01 - 31. No two-slave panels

are allowed to have the same number

assigned. Only one Master panel is allowed

on any one system.

Adjust reset (11)

Use the

to set the AmbiTec Plus to the

type of reset required. Type 01 is all relays

off and is used for those heaters with

automatic ignition where power to the

burner must be interrupted to cause burner

reset in case of burner lock out. Type 02 is

for use where a live or neutral is required to

be switched back to the heater unit to cause

burner reset.

Adjust V3 (12)

Use the

to change operation from

manual 'Vent' mode to V1 auto temperature

sensitive mode.

Adjust high fire time (13)

Use the

to set the time required for the

burner to be on high fire during light up for

proper ignition of the burner. The setting

may be from 00 - 99 seconds.

PLUS

ENERGY SAVING ELECTRONIC CONTROL PANEL

Adjust preheat mode (14)

Press the

to remain fixed at the time set in the adjust

preheat screen. Select 02 to allow the

controller to hold off the preheat to take

into account the actual ambient

temperature.

Adjust pre heat (15)

Use the

time from 0 hours to 4 hours in 30 minute

steps. Ideally this should be set to the time

it takes to raise the room temperature to

20˚C. Every on time will be advanced by

this preheat time.

Adjust day temperature band (16)

Use the

the

to set these to the lower end of the

range over which the day temperature may

be set in the normal display adjust screen.

Use the

to set the upper end of the range over

which the day temperature may be set in

the normal display adjust screen. The From

is adjustable from 00˚C to 50˚C and the To

is adjustable from 00˚C to 50˚C. However

the To reading can never be set lower than

the From reading.

Night temperature band (17)

Use the

the

to set these to set the lower end of

the range over which the day temperature

may be set in the normal display adjust

screen. Use the

Use the

range over which the day temperature may

be set in the normal display adjust screen.

The From is adjustable from 00˚C to 40˚C

and the To is adjustable from 00˚C to 50˚C.

However to To reading can never be set

lower than the From reading.

FWD clock 1 hour at 01:00 (18)

Use the

and the

to select the date position and the

to set the correct date for automatic clock

forward time.

to select 01 if the preheat is

to set the required preheat

to select 'From' reading. Use

to select To reading. Use the

to select From reading. Use

to select To reading.

to set the upper end of the

to move to the month position

to select the month. Use the

RTD clock 1 hour at 01:00 (19)

Use the

to move to the month position

and the

to select the month. Use the

to select the date position and the

to set the correct date for automatic

clock retard time.

Holiday (Covered only for frost

protection no night set back) (20)

Use the

to select the From date

position for the holiday period to start and

the

to set the date. Use the

select the From month position and the

to set the month. Use the

To date position for the holiday period to

end and the

to set the date. Use the

to select the To month position and the

to set the month.

Note If set the will turn off on the last OFF of

the From date and will turn back on again on

the first On of the To date.

Holiday 2 (21)

If required set a second holiday period as in

holiday 1.

Holiday 3 (22)

If required set a third holiday period as in

holiday 1.

Holiday 4 (23)

If required set a fourth holiday period as in

holiday 1.

Adjust Hand (24)

Use the

to adjust from 30 min. to 2

hours in 30 min steps.

to select the