Bobike Maxi+ Petunjuk Pengguna - Halaman 6

Jelajahi secara online atau unduh pdf Petunjuk Pengguna untuk Aksesori Sepeda Bobike Maxi+. Bobike Maxi+ 9 halaman.

Halaman Cetak

element with key 13, with the flat side against the

rear fork. Ensure that the socket is mounted hori-

zontally and with the T-shaped opening facing

upwards.

B Mounting using the ATB bracket

Secure the ATB bracket (J) with the supplied

screws, the brackets and the plastic washers to

the saddle tube. To do this, take the large bracket

together with the plastic washer and the long

screws, and place these on the saddle tube from

the front. Then take the other plastic washer and

the small bracket and place these to the rear

side of the saddle tube. Now mount the brackets

to each other using the screws and the supplied

Allen key. Hand-tighten the screws, because the

correct position must still be set. Now mount the

plastic socket using the two short screws between

the bracket. Ensure that the correct side (opening)

is pointing upwards and hand-tighten the screws.

Now secure both locking units (L) to the rear fork

approximately 30 cm below the socket (I). The loc-

king units are suitable for rear forks with a diameter

of between 12 and 25 mm. To adjust, insert the

clamp bracket of the locking unit in the first, middle

or rearmost slot.

Ensure that both locking units left and right are

secured at exactly the same height. Hand-tighten the

screws and the turn the knobs so as to create a slot

of about 1 cm.

The foot straps (F) must be fitted to the footrests (E)

before mounting. Mount the foot guards (K) and the

foot supports onto the footrest tube (D).

Adjust the height of the footrests

To set the correct height of the footrests (E), first

measure the length of your child's lower legs from

the underside of the knee to the sole of the foot. This

measurement must match the distance from the seat

to the underside of the footrest. This then gives the

height at which the footrests must be mounted.

Mounting the foot guards

Place one foot guard on the inside of the footrest

tube. Place a footrest on the outside of the support

www.bobike.com

tube and slide the long screw through the washer,

the footrest, the support tube and the foot guard.

Ensure that the elasticised band of the safety belt,

which is attached to the footrest tube, is not trapped

between the foot guard and the footrest tube. The

elasticised band belongs in the uppermost position

below the seat. Secure the nut plate to the inside of

the foot guard, parallel to the support tube. Now

tighten the screw firmly with a torque of 3 Nm.

Mount one of the short screws together with the

washer and the nut plate as far from the footrest as

possible, so that the foot guard sits securely. After

the other foot guard and footrest have been moun-

ted, you can place your seat on your bicycle.

Wheel contact guard

If you bicycle does not have a baggage carrier

then mount the extra wheel contact guard to the

foot guards. You can click this securely to the foot

guards. If the extra wheel contact guard also fits on

your bicycle with a baggage carrier, then secure the

guard as well.

Take the seat and insert the head of the mounting

bracket (C) straight and all the way into the socket.

Turn the footrest tube down, fit the ends into the

locking units and tighten the knobs. Ensure that the

outer ends of the footrest tubes are placed in the slot

as far as possible.

When adjusting the seat, the surface of the seat must

not tip forwards. The child could slide out of it. It is

recommended to angle the seatback slightly towards

the rear. Ensure that a space of at least 1 cm

remains between the seat and the baggage carrier

or the mudguard. The seat is correctly mounted

when the footrest tubes are at an angle of between

60 and 80 degrees. If the position of the seat is still

not right then move the locking units up or down, or

adjust the position of the ATB bracket (J) or the soc-

ket (I). When the correct position is reached, tighten

the locking units and the screws of the ATB bracket

or the nut of the socket with a torque of 10 Nm.

Tighten the short screws in the plastic socket until the

slack is taken up. The steel pin and the lock ensure a