Canon CR-N700 Panduan Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Kamera Digital Canon CR-N700. Canon CR-N700 4 halaman. Remote camera

Halaman Cetak

When installing the camera at a high place

use the ceiling plate to ﬁx the

camera

Fix the ceiling plate tightly with four M4 screws

(

pan head

head

etc

.).

When working with the camera upside down

support the camera to prevent

it from wobbling in order to attach or remove the rubber feet or the camera

mount safety wire

Keep the four rubber feet and four screws that have

been removed for reuse in case of a change in the installation

Ceiling mount

The camera is hung upside down from the ceiling or other location using the

ceiling plate

The procedure provided in the "Installation Guide

Important Information" [2

explains this installation method

The weight of the camera

(

body only

Approx

4 kg

7 lb

Reinforce the ceiling depending on its structure and

(

.).

material to ensure the sufficient holding strength to support the total weight

including the camera and the mounting parts

and install

Standing mount

The camera is ﬁxed to a high place using the ceiling plate

Follow the same procedure as for the ceiling mount

except for the direction

of the camera and logo plate inversion

Tripod mount

Attach the tripod by ﬁxing two screws to the two screw holes for tripod

Use 1

20UNC screws and tighten them securely

and set the tripod on a

ﬂat surface with no steps

Also refer to the instructions in the "Installation Guide

Important Information"

if necessary

1/4-20UNC

4.5 – 5.5 mm (0.18 – 0.22 in.)

Desktop

Install the camera on a stable

horizontal surface such as a table

Also refer to the instructions in the "Installation Guide

Important Information"

if necessary

Connecting the Camera

16 15

1. LAN terminal

This terminal is for a network connection

(

45 connector

The built

in PoE

Power over Ethernet

function allows the camera to be

++ (

++)

HUB that complies with IEEE802

3bt Type 3 or higher

via a LAN cable

Use a category 5e or higher STP

shielded type

LAN cable

up to 100 m

(

)

in length

Important

•

Some PoE

HUBs can limit the power for each port

but applying limits

may interfere with performance

In this case

do not limit the power

•

Some PoE

HUBs have limits for the total power consumption for

the ports

which can interfere with performance when multiple ports

are in use

For more information

check the instruction guide for the

corresponding PoE

HUB

2. SD card slot

binding

For future expansion

3. RESET switch

Initialize the camera settings to the factory defaults

Guide" for details

4. 12G-SDI OUT terminal

Terminal for 12G

SDI output

(

BNC

5. SERVICE switch

Set the camera number and frame frequency operated by the IR remote

)

controller

Refer to "Before using the camera" > "SERVICE switch settings"

(

6. TIME CODE terminal

Terminal for time code input

output

(

BNC

7. Memory card slot

For

future expansion

8. 3G-SDI OUT terminal

Terminal for 3G

SDI output

(

BNC

9. GEN-LOCK/SYNC terminal

Terminal for the synchronization signal input

output

videos from the camera and external devices

If the reference signal is unstable

external synchronization is not possible

Subcarriers do not synchronize

10. INPUT1/INPUT2 terminal

XLR terminals for audio input

It can be used for microphone

•

Microphone power

(

Phantom power

)

: 48 V DC

11. LED for phantom power supply

It is lit in blue when the phantom power is supplied

12. MIC terminal

Stereo

5 mm

14 in

terminal for audio input

(

microphone

line input

•

Microphone power: 2

4 V DC

9 10

13. RS-422 terminal

Serial terminal

(

45 connector

)

for RS

422

Connect the GNDs on both ends to stabilize the voltage level of the signal

Use category 5e or higher STP cables

Pin number

Function

Output

(-)

Output

(+)

Input

(-)

GND

–

GND

–

Input

(+)

–

14. HDMI OUT terminal

Terminal for HDMI output

15. DC IN 12V terminal

Pow

er supply terminal for the external DC power supply

Connect to the power supply that meets the installation site requirements

(

approved products and the environment

)

and product speciﬁcations

In addition

note that inrush current may cause the power supply to be

328 ft

(

insufﬁcient and cause failure when power is turned on

recommended to use a power supply with a power capacity of two to three

times the rated capacity or more

•

Input: 10

8 V

–

20 V DC

5 A

(

acceptable maximum load current

pin XLR connector

Pin number

Function

GND

–

20 V DC

16. GND terminal

Ground terminal of the camera

It is used to install a lightning arrester

Refer to the "Settings

Note

•

The camera is not equipped with a power switch

and off

insert and remove the cable of the external DC power supply

connected to the "15

DC IN 12V terminal" or the PoE

to the "1

LAN terminal"

When both the PoE

HUB and the external DC power supply are

connected

the external DC power supply takes priority

DC power supply is disconnected while both are connected

the camera will be interrupted

disconnecting and reconnecting the LAN cable

•

The audio input terminals

terminal"

and microphones should be set using the Settings Page

)

to the "Settings Guide" for details

Specifications

Please refer to the

Speciﬁcations

for speciﬁcations not listed below

BNC

to synchronize the

(

)

Pan operation range: Horizontal

Tilt operation range: Vertical

Operating Environment: Temperature: 0

Humidity: 10%

Storage Environment: Temperature: 0

Humidity: 10%

line input

Power Consumption: PoE

DC Input: Approx

Class 5

Dimensions

W x H x D

: Approx

(

)

(

excluding protrusions

Weight: Approx

4 kg

(

7 lb

It can be used for

Country Regulations

About wireless communication

Regarding countries and regions where radio communication functions are

acceptable

Since the utilization of the radio communication functions can be legally

restricted by a country or region

country or the region where the product is purchased

liable for any incidents that may incur as a result of the utilization of the

radio communication functions in any country or region other than where the

product is purchased

FCC NOTICE

Remote Camera

Model Name: CR

This device complies with Part 15 of the FCC Rules

to the following two conditions:

interference

and

this device must accept any interference received

(

)

including interference that may cause undesired operation

Note: This equipment has been tested and found to comply with the limits for

a Class A digital device

pursuant to Part 15 of the FCC Rules

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment

This equipment generates

and

if not installed and used in accordance with the user manual

harmful interference to radio communications

in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense

Do not make any changes or modifications to the equipment unless

otherwise specified in the manual

be made

you could be required to stop operation of the equipment

Therefore

it is

Use of shielded cable is required to comply with class A limits in Subpart B

of Part 15 of FCC Rules

Model: CR

N700

including WLAN Module Model ES202

(

IC: 498J

239

)

This device complies with Part 15 of FCC Rules and ISED

licenceexempt RSS standard

conditions:

this device may not cause interference

(

)

(

)

this device must accept anyinterference

cause undesired operation of this device

This equipment complies with FCC

forth for an uncontrolled environment and meets the FCC radio frequency

(

)

Exposure Guidelines and RSS

surge protection devices

(

Exposure rules

the radiator at least 20 cm or more away from person

This transmitter must not be co

other antenna or transmitter

To turn the camera on

FDA regulation

HUB connected

This product has not been evaluated by the Food and Drug Administration

which supplies power

(

FDA

)

for use as a medical device

medical applications

If the external

your legal advisor to determine whether FDA regulations apply

power to

In this case

power can be restored by

Complies with

IMDA Standards

(

"10

INPUT1

INPUT2 terminal"

"12

MIC

DB00671

Refer

European Union regulatory notices:

Remote Camera

Warning

This is a class A product

radio interference in which case the user may be required to take adequate

measures

in the

Appendix

of the "Settings Guide"

Use of shielded network cable is required to comply with Class A limits in

EN55032

170

Wireless LAN Specifications

° – +

Frequency range: 2

– +

104

)

Maximum output power: 9

90%

without condensation

–

(

)

– +

104

)

For EU

–

90%

(

without condensation

)

Hereby

Input: Approx

4 W

max

body only

. (

)

compliance with Directive 2014

7 W max

. (

body only

)

conformity is available at the following internet address:

(

0 W required

)

for power supply devices

http:

www

200 x 269 x 208 mm

87 x 10

59 x 8

19 in

(

)

For UK

.) (

body only

)

Hereby

in compliance with the relevant statutory requirements

declaration of conformity is available at the following internet address:

https:

www

Only for European Union and EEA

United Kingdom

These symbols indicate that this product is not to be disposed of with your

it may not be possible to utilize out of the

Canon shall not be

If a chemical symbol is printed beneath the symbol shown above

in accordance with the Battery Directive and the UK Batteries and

N700

Accumulators Regulations

Operation is subject

Cd = Cadmium

This device may not cause harmful

a concentration above an applicable threshold specified in the Battery

(

)

Directive and the UK Batteries and Accumulators Regulations

This product should be handed over to a designated collection point

on an authorized one

to an authorized collection site for recycling waste electrical and electronic

equipment

this type of waste could have a possible impact on the environment and

uses

and can radiate radio frequency energy

human health due to potentially hazardous substances that are generally

may cause

associated with EEE

Operation of this equipment

will contribute to the effective usage of natural resources

For more information about the recycling of this product

local city office

disposal service or visit www

If such changes or modifications should

CANON INC

Shimomaruko 3

Canon U

One Canon Park

FCC ID: AZD239

Tel No

CANON EUROPA N

s applicable

Bovenkerkerweg 59

(

Operation is subject to the following two

and

including interference that may

ISED radiation exposure limits set

102 of the ISED radio frequency

(

This equipment should be installed and operated keeping

s body

located or operated in conjunction with any

When incorporated into a system with

FDA regulations may apply

Therefore

please consult

Model Name: CR

N700

In a domestic environment this product may cause

401 MHz

–

473 MHz

48 dBm

Canon Inc

declares that the radio equipment type CR

N700 is in

The full text of the EU declaration of

canon

europe

com

documentation

Canon Inc

declares that the radio equipment type CR

N700 is

The full text of the

canon

europe

com

documentation

(

Norway

Iceland and Liechtenstein

)

household waste

according to the WEEE Directive

2012

the Battery Directive

2006

(

)

national legislation implementing those Directives and

the UK Waste Electrical and Electronic Equipment

Regulations and the UK Batteries and Accumulators

Regulations

this indicates that a heavy metal

(

Hg = Mercury

Pb = Lead

)

is present in this battery or accumulator at

for

one basis when you buy a new similar product or

(

EEE

)

and batteries and accumulators

Improper handling of

Your cooperation in the correct disposal of this product

please contact your

waste authority

approved scheme or your household waste

canon

europe

com

sustainability

approach

chome

Ohta

Tokyo 146

8501

Japan

Inc

Melville

NY 11747

800

CANON

(

800

652

2666

)

1185 XB Amstelveen

The Netherlands

)

and