Domyos TC 450 Panduan Petunjuk Pengoperasian - Halaman 16
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Treadmill Domyos TC 450. Domyos TC 450 19 halaman.
Juga untuk Domyos TC 450: Panduan Petunjuk Pengoperasian (18 halaman)
Halaman Cetak
019_028 TC450 GB.QXD
13/05/05
E
Check the treadmill lubrication every ten hours of use:
• If you feel that the treadmill makes more noise when it is in motion:
• Or in passing your hand between the wood plank and the belt (with the product unplugged), you determine that the plank
is dry.
To lubricate:
Turn it off at the main switch and remove the connector from the socket.
Raise the machine to put it carefully in a vertical position.
Use a rag to clean the inside of the mat whilst turning it manually to clean the entire surface. Return the machine to its usual
position. If the edges of the mat are damaged, check its alignment. If the stitching is ripped, please contact in your Décathlon
retailer.
Spray a silicon fluid (container supplied with the product, or a spray silicone) onto the mat, an easy and quick operation.
Loosen the mat and spray the silicon both sides of it making sure to cover the entire surface.
After spraying, realign the belt and readjust the tension (DO NOT LOOSEN THE MAT THAT SPRAY FROM UNDERNEATH).
Comment: Contact your Décathlon store for advice on an appropriate silicon liquid.
PROBLEM : My treadmill doesn't turn on.
1 - Make sure that the main switch on your treadmill is in position 1.
2 - Make sure that the electrical cord is properly connected to the power sup-
ply.
3 - Make sure that the power supply is working properly (plug a lamp into it).
4 - Make sure that the circuit breaker is not disconnected (press on the circuit
breaker).
If everything is in order and the problem persists, please contact after-sale ser-
vice at your store.
PROBLEM : My treadmill turns on but doesn't start.
1 - Make sure that the safety key is properly attached to its spot on the instru-
ment panel.
2 - Are you using the "start" key to begin?
3 - If everything is in order and the problem persists, please contact after-sale
service at your store.
PROBLEM : The speed of my treadmill is not constant
1 - Are you using an extension cord? If so, remove it and try again.
2 - Make sure that the electrical cord is properly connected to the power sup-
ply.
3 - Make sure that the moving belt is neither too tight nor too loose (see main-
tenance chapter).
If everything is in order and the problem persists, please contact the after-sale
service of your store.
14:44
Page 26
N
G
CARE AND MAINTENANCE
TREADMILL LUBRICATING
T R O U B L E S H O O T I N G A N D E R R O R C O D E S
L
I
MOVING
Your treadmill is fitted with rollers for easy movement.
Before moving the machine, ensure the main switch to is in position 0
and that the connector has been removed from the power.
Lift the treadmill chassis and move it as required.
Before moving the treadmill: check the raising piston is locked before
moving or putting it away.
Turn the treadmill forward to position it on the rollers.
When moving the treadmill, be sure you don't damage the electrical
cord connected to it. We suggest wrapping it around a lateral upright
so it remains on top of the product as it is moved
Once it is in the design position, blocked it using your foot and drop
it until it is in complete contact with the ground.
Note: every time the product is moved, it is advisable to adjust it hori-
zontally to begin using it.
PROBLEM : My treadmill displays E1 on the console
1 - Remove the safety key and reinsert it.
If E1 persists
2 - Shut off the power source of the treadmill using the main switch; then recon-
nect to the power source, remove the safety key, and reinsert it.
If E1 persists
3 - Make sure all the electrical connections were done properly when the tread-
mill was assembled (electrical contacts). Partially disassemble the treadmill
(following assembly steps in reverse) and make sure that no wiring was
damaged during assembly.
If E1 persists:
Please contact after-sale service at your store.
PROBLEM : My treadmill makes noise
1 - Make sure that the moving belt is properly centered (see maintenance
chapter).
2 - Make sure that the moving belt is properly tensioned (see maintenance
chapter).
3 - Make sure that the underside of the moving belt is totally clean (see
maintenance chapter).
4 - Make sure there is enough silicone under the moving belt (see maintenance
chapter).
If everything is in order and the problem persists, ask the customer to bring the
product back.
26
S
H