Draper 218031 Petunjuk Perakitan - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Perakitan untuk Layar Proyeksi Draper 218031. Draper 218031 2 halaman. Cinefold portable projection screen, truss-style cinefold portable projection screen

Halaman Cetak

Truss-Style Cinefold Portable Projection Screen by Draper

① Read instructions through completely before proceeding; retain for future

reference.

② Handle viewing surface with care; do not allow it to come in contact with

sharp or dirty objects.

③ Use Handy Cranks provided; failure to do so may lead to screen damage.

④ Make sure screen is level.

⑤ Do not write on viewing surface.

⑥ The ideal temperature range for assembling folding screens to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

Truss Assembly

① Remove pouch containing viewing surface from case and set aside.

Remove all aluminum assemblies.

② Unfold all folded aluminum assemblies completely, noting labels and

color-coded marks. Lock all hinges. Position Stage Right and Stage Left

sections in appropriate positions with snaps facing up. Top and Bottom

sections should be set with snaps facing down.

③ To increase frame rigidity, hinges on top and bottom frame sections have

rivnuts marked with red and green. Insert a Handy Crank through the

threadless rivnut (red) and tighten into the threaded rivnut (green).

④ Apply small sections marked "Stiffener Bars" to back of Bottom frame

section, using eight Handy Cranks each. Failure to use all Handy Cranks

may result in damage to screen frame. Turn Bottom frame section over so

snaps face up.

⑤ If your screen frame is less than 25' wide, repeat step 4 for Top frame sec-

tion. Frames 25' wide and over are equipped with a special full-width Stiff-

ener for the top frame section. To attach it, place Stiffener ﬂ at with green

rivnuts face down. Place top frame section on top of and at right angles

to Stiffener, over the green rivnuts. Insert and tighten standard Handy

Cranks. Install 45° angle braces to the Top frame section and Stiffener with

short Handy Cranks. Turn Top frame so snaps face up.

Caution: Make sure all hinges and joints are locked

before raising screen to standing position.

Anti-Sway

Stabilizers

Heavy-Duty

Legs

Form Cinefold_Inst12

Assembly Instructions

Caution

Rigid

Truss

Frame

Caution:

Make sure

screen is placed

on level surface.

Frame & Legs

Assemble with

Handy Cranks

Printed in U.S.A.

⑥ Join Top and Bottom to Stage Right and Stage Left, using two Handy

Cranks on each of the four corners. Match numbers on white labels, and

keep in mind that no Handy Crank should protrude outside screen frame.

⑦ Remove surface from pouch. With the row of male snaps at bottom, posi-

tion screen surface over frame. Snap each of the four corners, then snap

across bottom, up sides, and across top.

⑧ Attach feet to inner side of legs with Handy Cranks, matching color-coded

markings. Attach legs to Stage Right and Stage Left with Handy Cranks,

matching colored tapes.

⑨ Raise screen to a vertical position. Add Heavy-Duty Legs and Anti-Sway

Stabilizers with Handy Cranks in the positions indicated below.

Handy Crank

Caution:

Beware of

pinch points.

Warning: This product is intended for indoor use only. Failure to

follow warning may result in product damage or personal injury due to

unforeseen acts of nature.

A Note About Surfaces

① Always fold with snaps face-to-face. Do not permit screen fabric to

contact border material or snaps when folded. Store in pouch

provided.

② Take care at all times not to permit Cinefold viewing surface to contact any

dusty or dirty area, nor any varnished or painted object.

③ When necessary, clean Cinefold viewing surface according to cleaning

instructions for the particular surface you are using. Surface must be com-

pletely dry before folding.

Valance Bar

Drapery

Bar

Adjustable Skirt Bar

Dress-Up Kit Assembly

PLEASE NOTE: All components are labeled and color coded to

facilitate assembly.

A. Valance Bar attaches to frame with simple bayonet-style mounting.

B. Draper Bars mount to Valance Bar, bayonet-style.

C. Optional adjustable Skirt Bar is secured to frame at desired level with

positive-locking plunger mechanism. If Skirt Bar is not used, Skirt may

be snapped to bottom of viewing surface.

D. Valance, Drapes, and Skirt snap onto Mounting Bars.

E. Gaps between the frame and the valance can be easily removed by

pulling the bottom edge of the valance to close the gap.

F. Pulling and smoothing the edges of the panels will remove any

wrinkles or puckers that might be present when product is unfolded.

Drapery

Bar