Bosch WAE18060AU Buku Petunjuk - Halaman 2

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Mesin cuci Bosch WAE18060AU. Bosch WAE18060AU 8 halaman.

Halaman Cetak
Safety instructions
Care
– Read the instruction manual and installation instructions and all other information enclosed
with the washing machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent
children from locking themselves in and risking their lives.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of
children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Items of laundry pretreated with cleaning agents containing
1. Pull out, press insert down, remove drawer completely.
solvents, e.g. stain remover/cleaning solvent may cause an
explosion after being loaded into the washing machine.
2. To remove the insert: press the insert upwards from below with your
Rinse items of laundry thoroughly by hand beforehand.
Risk of injury
– The washing machine door can become very hot.
3. Clean the detergent dispenser tray and insert with water and a brush and
– Be careful when draining hot detergent solution.
– Do not climb onto the washing machine.
4. Attach the insert and engage (connect the cylinder to the guide pin).
– Do not lean on the open washing machine door.
5. Push in the detergent drawer.
– Do not reach into the drum if it is still rotating.
– Be careful when opening the detergent drawer while the machine
is in operation.
Consumption values
Electricity
Programme
Load
Water**
Programme
duration**
consumption**
Cotton
40 °C
6,5 kg
0.46 kWh
55 l
100 min
Cotton
60 °C*
6,5 kg
1.07 kWh
55 l
117 min
Information to indicator lights
Cotton
Stains
60 °C
6,5 kg
1.20 kWh
55 l
135 min
Cotton
90 °C
6,5 kg
2.40 kWh
68 l
125 min
Indicator lights for status displays and/or buttons flash:
Easy-care
40 °C
3 kg
0.55 kWh
48 l
75 min
Indicator lights
Rinse and Wash
Delicate 30 °C
2 kg
0.28 kWh
48 l
44 min
flash
Wool
30 °C
2 kg
0.20 kWh
32 l
53 min
Indicator lights
* Programme setting wth maximum spin speed for testing according to or in accordance with AS/NZS 2040.2 and
Spin and Wash flash
AS/NZS 6400.
Indicator lights
** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient
Spin and Rinse flash
temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected
additional functions.
Indicator light
Rinse flashes
All indicator lights
flash
8
8
7
– Risk of electric shock.
Maintenance
Disconnect the mains plug.
– Risk of explosion. No solvents.
Before washing for the first time
Detergent solution pump
Do not put any washing in the machine. Turn on the tap, add approximately 1 litre of water
Turn the programme selector to Off and disconnect the mains plug.
and then ½ a measuring cup of detergent into compartment II. Turn the programme selector
1. Open and remove the service flap.
to Easy-care
60 °C and select Start/Pause
. At the end of the programme, turn the
programme selector to Off.
Machine housing, control panel
2. For models with a drainage hose: Remove the drainage hose from the
– Wipe with a soft, damp cloth.
retainer and pull it from the housing. Remove the container.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
Remove the sealing cap, allow the detergent solution to flow out.
Replace the sealing cap and place the drainage hose in the retainer.
– Remove detergent and cleaning agent residue immediately.
– Do not clean with a jet of water.
2* For models without a drainage hose: Carefully unscrew the pump cover
Cleaning the detergent drawer ...
until the detergent solution begins to flow out. When the service flap is
half full, close the pump cover and empty the service flap. Repeat the
... if it contains detergent or fabric softener residues.
above steps until all the detergent solution has completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in
the detergent solution pump must rotate).
5. Replace the pump cover and screw it tightly.
finger.
6. Place the service flap back on and close.
dry it.
To prevent unused detergent from flowing straight into the drain during the next wash:
Leave the detergent drawer open so that any residual water can
Pour 1 litre of water into compartment II and start the Drain
evaporate.
Drainage hose at the siphon
Drum
Turn the programme selector to Off and disconnect the mains plug.
Leave the washing machine door open so that the drum can dry out.
1. Loosen the hose clamp, carefully remove the drainage hose
Rust stains - use chlorine-free cleaning agent, not steel wool.
(residual water).
Descaling
Ensure there is no laundry in the machine
2. Clean the drainage hose and siphon connecting piece.
Descale the appliance according to the descaler manufacturer's instructions. This should not
3. Reattach the drainage hose and secure the connection with the hose
be necessary if the correct dosage of detergent is used.
clamp.
Filter in the water supply
Risk of electric shock
Do not immerse the HydroSafe safety device in water (contains an electric valve).
Close the washing machine door properly; laundry may be caught.
Reduce the water pressure in the supply hose:
1. Turn off the tap.
Open the tap completely, supply hose kinked or trapped;
2. Select any programme (except Spin
Clean the filter –> page 10, Water pressure too low.
3. Select Start/Pause
seconds.
Detergent solution pump blocked; Clean the detergent solution pump
–> page 10.
4. Turn the programme selector to Off. Disconnect the mains plug.
Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon
Clean the filter:
–> page 10.
1. Depending on model:
Motor fault. Call the after-sales service.
Disconnect the hose from the tap.
Clean the filter using a small brush.
Motor fault. Call the after-sales service.
and/or for Standard and HydroSafe models:
Remove the hose on the rear of the appliance,
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
9
– Risk of scalding. Allow the
detergent solution to cool down.
What to do if ...
– Turn off the tap.
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
– Start/Pause
Detergent not dispensed.
– Tap not turned on?
– Filter blocked? Clean the filter –> page 10.
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Wait approx. 2 minutes.
cannot be opened.
Programme does not
– Start/Pause
start.
– Washing machine door closed?
Detergent solution is not
– Clean the detergent solution pump –> page 10.
drained.
– Clean the waste pipe and/or drainage hose.
Water not visible in the
– Not a fault - water below the visible area.
drum.
Spin result not
– Distribute large and small items of laundry evenly in the drum.
satisfactory.
Spin cycle performed
– Not a fault - unbalanced load detection system adjusts the
several times.
imbalance.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary –> page 9.
products.
Odour formation in the
– Run programme Cotton
washing machine.
standard detergent.
programme.
Foam escaping from the
– Too much detergent used?
detergent drawer.
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour
into compartment II (not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
Intense noise formation,
– Are the appliance feet fixed?
vibrations and
Secure the appliance feet –> Installation instructions.
"wandering" during the
– Transportation safety devices removed?
spin cycle.
Remove the transportation safety devices –> Installation
instructions.
Display panel/indicator
– Power cut?
lamps do not function
– Fuses triggered? Reset/change the fuses.
during operation.
– If the fault occurs repeatedly, call the after-sales service.
Programme sequence
– Not a fault - unbalanced load detection system adjusts
longer than usual.
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
/Drain
).
rinse cycle.
. Let the programme run for approximately 40
Detergent residues on
– Occasionally, phosphate-free detergents contain water-insoluble
the laundry.
residues.
– Select Rinse
If you cannot correct a fault yourself or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service –> Installation instructions.
10
not selected?
selected?
Washing machine
90 °C without laundry. Use
Instruction manual
or brush the laundry after washing.
Observe the safety instructions on page 8.
Read these instructions and the separate installation instructions
before operating the washing machine.
11
en