Bosch WAE18060AU Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Spryskiwacz Bosch WAE18060AU. Bosch WAE18060AU 8 stron.

Drukuj stronę

Safety instructions

Care

– Read the instruction manual and installation instructions and all other information enclosed

with the washing machine and act accordingly.

– Retain the documents for subsequent use.

Risk of electric shock

– Never pull the cable to disconnect the mains plug.

– Never insert/disconnect the mains plug with damp hands.

Danger to life

For worn-out appliances:

– Disconnect the mains plug.

– Sever the mains cable and discard along with the plug.

– Destroy the lock on the washing machine door. This will prevent

children from locking themselves in and risking their lives.

Danger of suffocation

– Keep packaging, film and packaging parts out of the reach of

children.

Risk of poisoning

– Keep detergents and care products out of the reach of children.

Risk of explosion

– Items of laundry pretreated with cleaning agents containing

1. Pull out, press insert down, remove drawer completely.

solvents, e.g. stain remover/cleaning solvent may cause an

explosion after being loaded into the washing machine.

2. To remove the insert: press the insert upwards from below with your

Rinse items of laundry thoroughly by hand beforehand.

Risk of injury

– The washing machine door can become very hot.

3. Clean the detergent dispenser tray and insert with water and a brush and

– Be careful when draining hot detergent solution.

– Do not climb onto the washing machine.

4. Attach the insert and engage (connect the cylinder to the guide pin).

– Do not lean on the open washing machine door.

5. Push in the detergent drawer.

– Do not reach into the drum if it is still rotating.

– Be careful when opening the detergent drawer while the machine

is in operation.

Consumption values

Electricity

Programme

Load

Water**

Programme

duration**

consumption**

Cotton

40 °C

6,5 kg

0.46 kWh

55 l

100 min

Cotton

60 °C*

6,5 kg

1.07 kWh

55 l

117 min

Information to indicator lights

Cotton

Stains

60 °C

6,5 kg

1.20 kWh

55 l

135 min

Cotton

90 °C

6,5 kg

2.40 kWh

68 l

125 min

Indicator lights for status displays and/or buttons flash:

Easy-care

40 °C

3 kg

0.55 kWh

48 l

75 min

Indicator lights

Rinse and Wash

Delicate 30 °C

2 kg

0.28 kWh

48 l

44 min

flash

Wool

30 °C

2 kg

0.20 kWh

32 l

53 min

Indicator lights

* Programme setting wth maximum spin speed for testing according to or in accordance with AS/NZS 2040.2 and

Spin and Wash flash

AS/NZS 6400.

Indicator lights

** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient

Spin and Rinse flash

temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected

additional functions.

Indicator light

Rinse flashes

All indicator lights

flash

– Risk of electric shock.

Maintenance

Disconnect the mains plug.

– Risk of explosion. No solvents.

Before washing for the first time

Detergent solution pump

Do not put any washing in the machine. Turn on the tap, add approximately 1 litre of water

Turn the programme selector to Off and disconnect the mains plug.

and then ½ a measuring cup of detergent into compartment II. Turn the programme selector

1. Open and remove the service flap.

to Easy-care

60 °C and select Start/Pause

. At the end of the programme, turn the

programme selector to Off.

Machine housing, control panel

2. For models with a drainage hose: Remove the drainage hose from the

– Wipe with a soft, damp cloth.

retainer and pull it from the housing. Remove the container.

– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).

Remove the sealing cap, allow the detergent solution to flow out.

Replace the sealing cap and place the drainage hose in the retainer.

– Remove detergent and cleaning agent residue immediately.

– Do not clean with a jet of water.

2* For models without a drainage hose: Carefully unscrew the pump cover

Cleaning the detergent drawer ...

until the detergent solution begins to flow out. When the service flap is

half full, close the pump cover and empty the service flap. Repeat the

... if it contains detergent or fabric softener residues.

above steps until all the detergent solution has completely drained out.

3. Carefully unscrew the pump cover (residual water).

4. Clean the interior, pump cover thread and pump housing (the impeller in

the detergent solution pump must rotate).

5. Replace the pump cover and screw it tightly.

finger.

6. Place the service flap back on and close.

dry it.

To prevent unused detergent from flowing straight into the drain during the next wash:

Leave the detergent drawer open so that any residual water can

Pour 1 litre of water into compartment II and start the Drain

evaporate.

Drainage hose at the siphon

Drum

Turn the programme selector to Off and disconnect the mains plug.

Leave the washing machine door open so that the drum can dry out.

1. Loosen the hose clamp, carefully remove the drainage hose

Rust stains - use chlorine-free cleaning agent, not steel wool.

(residual water).

Descaling

Ensure there is no laundry in the machine

2. Clean the drainage hose and siphon connecting piece.

Descale the appliance according to the descaler manufacturer's instructions. This should not

3. Reattach the drainage hose and secure the connection with the hose

be necessary if the correct dosage of detergent is used.

clamp.

Filter in the water supply

Risk of electric shock

Do not immerse the HydroSafe safety device in water (contains an electric valve).

Close the washing machine door properly; laundry may be caught.

Reduce the water pressure in the supply hose:

1. Turn off the tap.

Open the tap completely, supply hose kinked or trapped;

2. Select any programme (except Spin

Clean the filter –> page 10, Water pressure too low.

3. Select Start/Pause

seconds.

Detergent solution pump blocked; Clean the detergent solution pump

–> page 10.

4. Turn the programme selector to Off. Disconnect the mains plug.

Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon

Clean the filter:

–> page 10.

1. Depending on model:

Motor fault. Call the after-sales service.

Disconnect the hose from the tap.

Clean the filter using a small brush.

Motor fault. Call the after-sales service.

and/or for Standard and HydroSafe models:

Remove the hose on the rear of the appliance,

Remove the filter with pliers and clean.

2. Connect the hose and check for leaks.

– Risk of scalding. Allow the

detergent solution to cool down.

What to do if ...

– Turn off the tap.

Water is leaking out.

– Attach/replace the drainage hose correctly.

– Tighten the screw connection of the supply hose.

No water supply.

– Start/Pause

Detergent not dispensed.

– Tap not turned on?

– Filter blocked? Clean the filter –> page 10.

– Supply hose kinked or trapped?

Washing machine door

– Safety function active. Wait approx. 2 minutes.

cannot be opened.

Programme does not

– Start/Pause

start.

– Washing machine door closed?

Detergent solution is not

– Clean the detergent solution pump –> page 10.

drained.

– Clean the waste pipe and/or drainage hose.

Water not visible in the

– Not a fault - water below the visible area.

drum.

Spin result not

– Distribute large and small items of laundry evenly in the drum.

satisfactory.

Spin cycle performed

– Not a fault - unbalanced load detection system adjusts the

several times.

imbalance.

Residual water in the

– Not a fault - the action of the care product is not affected.

compartment for care

– Clean the insert if necessary –> page 9.

products.

Odour formation in the

– Run programme Cotton

washing machine.

standard detergent.

programme.

Foam escaping from the

– Too much detergent used?

detergent drawer.

If foam is escaping from the detergent drawer:

Mix 1 tablespoon of fabric softener with ½ litre of water and pour

into compartment II (not with outdoor or down fabrics).

– Reduce the detergent dosage for the next wash cycle.

Intense noise formation,

– Are the appliance feet fixed?

vibrations and

Secure the appliance feet –> Installation instructions.

"wandering" during the

– Transportation safety devices removed?

spin cycle.

Remove the transportation safety devices –> Installation

instructions.

Display panel/indicator

– Power cut?

lamps do not function

– Fuses triggered? Reset/change the fuses.

during operation.

– If the fault occurs repeatedly, call the after-sales service.

Programme sequence

– Not a fault - unbalanced load detection system adjusts

longer than usual.

imbalance by repeatedly distributing the laundry.

– Not a fault - foam detection system active - adds an additional

/Drain

rinse cycle.

. Let the programme run for approximately 40

Detergent residues on

– Occasionally, phosphate-free detergents contain water-insoluble

the laundry.

residues.

– Select Rinse

If you cannot correct a fault yourself or a repair is required:

– Turn the programme selector to Off and remove the mains plug from the socket.

– Turn off the water supply and call the after-sales service –> Installation instructions.

not selected?

selected?

Washing machine

90 °C without laundry. Use

Instruction manual

or brush the laundry after washing.

Observe the safety instructions on page 8.

Read these instructions and the separate installation instructions

before operating the washing machine.