Bosch WAE24060 Buku Petunjuk - Halaman 2

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Mesin cuci Bosch WAE24060. Bosch WAE24060 8 halaman. Bosch washing machine instruction manual

Halaman Cetak

Safety instructions

Care

– Read the instruction manual and installation instructions and all other information enclosed

with the washing machine and act accordingly.

– Retain the documents for subsequent use.

Risk of electric shock

– Never pull the cable to disconnect the mains plug.

– Never insert/disconnect the mains plug with damp hands.

Danger to life

For worn-out appliances:

– Disconnect the mains plug.

– Sever the mains cable and discard along with the plug.

– Destroy the lock on the washing machine door. This will prevent

children from locking themselves in and risking their lives.

Danger of suffocation

– Keep packaging, film and packaging parts out of the reach of

children.

Risk of poisoning

– Keep detergents and care products out of the reach of children.

Risk of explosion

– Items of laundry pretreated with cleaning agents containing

solvents, e.g. stain remover/cleaning solvent may cause an

explosion after being loaded into the washing machine.

1. Pull out, press insert down, remove draw completely.

Rinse items of laundry thoroughly by hand beforehand.

2. To remove the insert: press the insert upwards from below with your

Risk of injury

– The washing machine door can become very hot.

3. Clean the detergent dispenser tray and insert with water and a brush and

– Be careful when draining hot detergent solution.

– Do not climb onto the washing machine.

4. Attach the insert and engage (connect the cylinder to the guide pin).

– Do not lean on the open washing machine door.

5. Push in the detergent drawer.

– Do not reach into the drum if it is still rotating.

– Be careful when opening the detergent drawer while the machine

is in operation.

Consumption values

depending on model

Programme

Load

Electricity***

Water***

duration***

Cottons 40 °C*

6 kg

0,85 kWh

58 l

01:50 h

Cottons 60 °C*

6 kg

1,40 kWh

57 l

02:05 h

Cottons 90 °C

6 kg

2,10 kWh

62 l

02:05 h

Information to indicator lights

Easy-Care 40 °C*

3 kg

0,55 kWh

48 l

01:15 h

Indicator lights for status displays and/or buttons flash:

Delicates 30 °C

2 kg

0,28 kWh

48 l

00:44 h

Indicator lights

Wool 30 °C

2 kg

0,20 kWh

32 l

00:53 h

Rinse and

* Programme setting for testing in accordance with valid standard EN60456.

Wash flash

Note on comparative tests: For testing the test programmes, wash the specified load using the maximum spin speed

Indicator lights

( depending on model ).

Spin and

Annual energy

Annual water

Wash flash

Programme

Load

consumption

Indicator lights

Cottons 40 °C** /

6/3kg

193kWh

9600 l

Spin and

Rinse flash

Cottons Intensive Stains 60 °C**

** Programme setting for testing and energy labelling in accordance with EU directive 2010/30/EU with cold water (15 ºC).

Indicator light

*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-

Rinse flashes

perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional

functions.

All indicator lights flash

– Risk of electric shock. Disconnect the mains plug.

Maintenance

– Risk of explosion. No solvents.

Before washing for the first time

Detergent solution pump

Do not load any laundry into the machine. Turn on the tap.

Turn the programme selector to Off and disconnect the mains plug.

Add the following to compartment II:

1. Open and remove the service flap.

– approx. 1 litre water

– detergent (dosage according to the manufacturer's instructions for light soiling and the

appropriate degree of water hardness)

Set the programme selector to Easy-Care 60 °C and select Start. At the end of the

2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it

programme, turn the programme selector to Off.

from the housing. Remove the container.

Remove the sealing cap, allow the detergent solution to flow out.

Machine housing, control panel

Replace the sealing cap and place the drainage hose in the retainer.

– Wipe with a soft, damp cloth.

– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).

– Remove detergent and cleaning agent residue immediately.

2* For models without a drainage hose: Carefully unscrew the pump cover until the

– Do not clean with a jet of water.

detergent solution begins to flow out. When the service flap is half full, close the pump cover

and empty the service flap. Repeat the above steps until all the detergent solution has

Cleaning the detergent drawer ...

completely drained out.

... if it contains detergent or fabric softener residues.

3. Carefully unscrew the pump cover (residual water).

4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent

solution pump must rotate).

5. Replace the pump cover and screw it tightly in place.

finger.

6. Place the service flap back on and close.

dry it.

To prevent unused detergent from flowing straight into the drain during the next wash: pour 1 litre of water into

Leave the detergent drawer open so that any residual water can

compartment II and start the Drain programme.

evaporate.

Drainage hose at the siphon

Drum

Turn the programme selector to Off and disconnect the mains plug.

Leave the washing machine door open so that the drum can dry out.

1. Loosen the hose clamp, carefully remove the drainage hose (residual water).

Rust stains - use chlorine-free cleaning agent, not steel wool.

2. Clean the drainage hose and siphon connecting piece.

Descaling

3. Reattach the drainage hose and secure the connection with the hose clamp.

Ensure there is no laundry in the machine

Filter in the water supply

Descale the appliance according to the descaler manufacturer's instructions. This should not

be necessary if the correct dosage of detergent is used.

Reduce the water pressure in the supply hose:

1. Turn off the tap.

2. Select any programme (except for Spin, Drain).

3. Select Start. Let the programme run for approximately 40 seconds.

Close the washing machine door properly; laundry may be caught.

4. Turn the programme selector to Off. Disconnect the mains plug.

Clean the filter:

Open the tap completely, supply hose kinked or trapped;

1. Depending on model:

Clean the filter

page 10, Water pressure too low.

Disconnect the hose from the tap.

Clean the filter using a small brush.

Detergent solution pump blocked; Clean the detergent solution pump

page 10.

and/or for Standard and Aqua-Secure models:

Drainage hose/waste pipe blocked; Clean the drainage hose at the

siphon

page 10.

Remove the hose on the rear of the appliance.

Remove the filter with pliers and clean.

Motor fault. Call the after-sales service.

2. Connect the hose and check for leaks.

Turn off the tap and call the after-sales service.

– Risk of scalding.

What to do if ...

Allow the detergent solution to cool down.

– Turn off the tap.

Water is leaking out.

– Attach/replace the drainage hose correctly.

– Tighten the screw connection of the supply hose.

No water supply.

– Start not selected?

Detergent not dispensed.

– Tap not turned on?

– Filter blocked? Clean the filter

page 10.

– Supply hose kinked or trapped?

Washing machine door

– Safety function active. Wait approx. 2 minutes.

cannot be opened.

Programme does not start.

– Start selected?

– Washing machine door closed?

Detergent solution is not

– Clean the detergent solution pump

page 10.

drained.

– Clean the waste pipe and/or drainage hose.

Water not visible in the drum. – Not a fault - water below the visible area.

Unsatisfactory spin result.

– Not a fault - the unbalanced-load detection system has cancelled the spin

Laundry wet/too damp.

cycle because of uneven distribution of the laundry.

Distribute small and large items of laundry evenly inside the drum.

Spin cycle performed several

– Not a fault - unbalanced load detection system adjusts the imbalance.

times.

Residual water in the

– Not a fault - the action of the care product is not affected.

compartment for care

– Clean the insert if necessary

page 9.

products.

Odour formation in the

– Run programme Cottons 90 °C without laundry. Use standard detergent.

washing machine.

Foam escaping from the

– Too much detergent used?

detergent drawer.

If foam is escaping from the detergent drawer:

Mix 1 tablespoon of fabric softener with ½ litre of water and pour into

compartment II (not with outdoor or down fabrics).

– Reduce the detergent dosage for the next wash cycle.

Intense noise formation,

– Are the appliance feet fixed?

vibrations and "walking"

Secure the appliance feet

Installation instructions.

during the spin cycle.

– Transportation safety devices removed?

Remove the transportation safety devices

Noises during spin and drain

– Clean detergent-solution pump

page 10

cycles.

The indicator lights do not

– Power cut?

function during operation.

– Fuses tripped? Reset/change the fuse.

– If the fault occurs repeatedly, call the after-sales service.

Programme sequence longer

– Not a fault - unbalanced load detection system adjusts imbalance by

than usual.

repeatedly distributing the laundry.

– Not a fault - foam detection system active - adds an additional rinse cycle.

Detergent residues on the

– Occasionally, phosphate-free detergents contain water-insoluble residues.

laundry.

– Select Rinse or brush out the laundry after washing.

If you cannot correct a fault yourself (switching on/off) or a repair is required:

– Turn the programme selector to Off and remove the mains plug from the socket.

– Turn off the water supply and call the after-sales service

Installation instructions.

Washing machine

en Instruction manual