Bosch WAE24060 Manuale di istruzioni - Pagina 2
Sfoglia online o scarica il pdf Manuale di istruzioni per Lavatrice Bosch WAE24060. Bosch WAE24060 8. Bosch washing machine instruction manual
Safety instructions
Care
– Read the instruction manual and installation instructions and all other information enclosed
with the washing machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent
children from locking themselves in and risking their lives.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of
children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Items of laundry pretreated with cleaning agents containing
solvents, e.g. stain remover/cleaning solvent may cause an
explosion after being loaded into the washing machine.
1. Pull out, press insert down, remove draw completely.
Rinse items of laundry thoroughly by hand beforehand.
2. To remove the insert: press the insert upwards from below with your
Risk of injury
– The washing machine door can become very hot.
3. Clean the detergent dispenser tray and insert with water and a brush and
– Be careful when draining hot detergent solution.
– Do not climb onto the washing machine.
4. Attach the insert and engage (connect the cylinder to the guide pin).
– Do not lean on the open washing machine door.
5. Push in the detergent drawer.
– Do not reach into the drum if it is still rotating.
– Be careful when opening the detergent drawer while the machine
is in operation.
Consumption values
depending on model
Programme
Programme
Load
Electricity***
Water***
duration***
Cottons 40 °C*
6 kg
0,85 kWh
58 l
01:50 h
Cottons 60 °C*
6 kg
1,40 kWh
57 l
02:05 h
Cottons 90 °C
6 kg
2,10 kWh
62 l
02:05 h
Information to indicator lights
Easy-Care 40 °C*
3 kg
0,55 kWh
48 l
01:15 h
Indicator lights for status displays and/or buttons flash:
Delicates 30 °C
2 kg
0,28 kWh
48 l
00:44 h
Indicator lights
Wool 30 °C
2 kg
0,20 kWh
32 l
00:53 h
Rinse and
* Programme setting for testing in accordance with valid standard EN60456.
Wash flash
Note on comparative tests: For testing the test programmes, wash the specified load using the maximum spin speed
Indicator lights
( depending on model ).
Spin and
Annual energy
Annual water
Wash flash
Programme
Load
consumption
consumption
Indicator lights
Cottons 40 °C** /
6/3kg
193kWh
9600 l
Spin and
Rinse flash
Cottons Intensive Stains 60 °C**
** Programme setting for testing and energy labelling in accordance with EU directive 2010/30/EU with cold water (15 ºC).
Indicator light
*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-
Rinse flashes
perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
functions.
All indicator lights flash
7
8
– Risk of electric shock. Disconnect the mains plug.
Maintenance
– Risk of explosion. No solvents.
Before washing for the first time
Detergent solution pump
Do not load any laundry into the machine. Turn on the tap.
Turn the programme selector to Off and disconnect the mains plug.
Add the following to compartment II:
1. Open and remove the service flap.
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the
appropriate degree of water hardness)
Set the programme selector to Easy-Care 60 °C and select Start. At the end of the
2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it
programme, turn the programme selector to Off.
from the housing. Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Machine housing, control panel
Replace the sealing cap and place the drainage hose in the retainer.
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Remove detergent and cleaning agent residue immediately.
2* For models without a drainage hose: Carefully unscrew the pump cover until the
– Do not clean with a jet of water.
detergent solution begins to flow out. When the service flap is half full, close the pump cover
and empty the service flap. Repeat the above steps until all the detergent solution has
Cleaning the detergent drawer ...
completely drained out.
... if it contains detergent or fabric softener residues.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent
solution pump must rotate).
5. Replace the pump cover and screw it tightly in place.
finger.
6. Place the service flap back on and close.
dry it.
To prevent unused detergent from flowing straight into the drain during the next wash: pour 1 litre of water into
Leave the detergent drawer open so that any residual water can
compartment II and start the Drain programme.
evaporate.
Drainage hose at the siphon
Drum
Turn the programme selector to Off and disconnect the mains plug.
Leave the washing machine door open so that the drum can dry out.
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
Rust stains - use chlorine-free cleaning agent, not steel wool.
2. Clean the drainage hose and siphon connecting piece.
Descaling
3. Reattach the drainage hose and secure the connection with the hose clamp.
Ensure there is no laundry in the machine
Filter in the water supply
Descale the appliance according to the descaler manufacturer's instructions. This should not
be necessary if the correct dosage of detergent is used.
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except for Spin, Drain).
3. Select Start. Let the programme run for approximately 40 seconds.
Close the washing machine door properly; laundry may be caught.
4. Turn the programme selector to Off. Disconnect the mains plug.
Clean the filter:
Open the tap completely, supply hose kinked or trapped;
1. Depending on model:
Clean the filter
page 10, Water pressure too low.
Disconnect the hose from the tap.
Clean the filter using a small brush.
Detergent solution pump blocked; Clean the detergent solution pump
page 10.
and/or for Standard and Aqua-Secure models:
Drainage hose/waste pipe blocked; Clean the drainage hose at the
siphon
page 10.
Remove the hose on the rear of the appliance.
Remove the filter with pliers and clean.
Motor fault. Call the after-sales service.
2. Connect the hose and check for leaks.
Turn off the tap and call the after-sales service.
9
– Risk of scalding.
What to do if ...
Allow the detergent solution to cool down.
– Turn off the tap.
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
– Start not selected?
Detergent not dispensed.
– Tap not turned on?
– Filter blocked? Clean the filter
page 10.
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Wait approx. 2 minutes.
cannot be opened.
Programme does not start.
– Start selected?
– Washing machine door closed?
Detergent solution is not
– Clean the detergent solution pump
page 10.
drained.
– Clean the waste pipe and/or drainage hose.
Water not visible in the drum. – Not a fault - water below the visible area.
Unsatisfactory spin result.
– Not a fault - the unbalanced-load detection system has cancelled the spin
Laundry wet/too damp.
cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
Spin cycle performed several
– Not a fault - unbalanced load detection system adjusts the imbalance.
times.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary
page 9.
products.
Odour formation in the
– Run programme Cottons 90 °C without laundry. Use standard detergent.
washing machine.
Foam escaping from the
– Too much detergent used?
detergent drawer.
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour into
compartment II (not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
Intense noise formation,
– Are the appliance feet fixed?
vibrations and "walking"
Secure the appliance feet
Installation instructions.
during the spin cycle.
– Transportation safety devices removed?
Remove the transportation safety devices
Noises during spin and drain
– Clean detergent-solution pump
page 10
cycles.
The indicator lights do not
– Power cut?
function during operation.
– Fuses tripped? Reset/change the fuse.
– If the fault occurs repeatedly, call the after-sales service.
Programme sequence longer
– Not a fault - unbalanced load detection system adjusts imbalance by
than usual.
repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse cycle.
Detergent residues on the
– Occasionally, phosphate-free detergents contain water-insoluble residues.
laundry.
– Select Rinse or brush out the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
Installation instructions.
10
Installation instructions.
Washing machine
en Instruction manual
11