Atkinson Electronics GSCM Manual - Halaman 5

Jelajahi secara online atau unduh pdf Manual untuk Unit Kontrol Atkinson Electronics GSCM. Atkinson Electronics GSCM 16 halaman. Generator start control module
Juga untuk Atkinson Electronics GSCM: Petunjuk Pengoperasian dan Pemasangan (16 halaman)

Halaman Cetak

GSCM Starting Sequence

The GSCM indicates that it is ready to receive a start signal by blinking the start LED once every 5 seconds. The GSCM is started by

shorting terminal 5 to ground (terminal 6) for manual start mode. The module may also start in automatic mode based on a battery

voltage, See AUTOMATIC STARTING FOR BATTERY CHARGING section, or a 30 day exercise cycle. The start LED is lit continuously to

indicate that a manual start signal has been applied. The various adjustment LEDs blink during their respective generator controller

time delay periods. If the GSCM detects an AC frequency input greater than zero (the generator is already running) it will not execute

a start sequence, but will light the Hz LED continuously. The generator starting sequence is as follows:

1. The start LED blinks once every 5 seconds to indicate that the GSCM is in ready mode. When a manual start signal is

received, the start LED lights constantly. After a 5 second delay, K4 (shutdown) relay closes to ensure the generator is not

running before beginning the cranking sequence. After 7 seconds the K1 (glow plug) relay closes to energize the glow

plug(s). The K1 relay remains closed until either the generator starts or the max crank time is reached.

2. An adjustable 5 to 60 second crank delay period starts when the K1 (glow plug) relay is energized.

3. After the crank delay period, K2 (crank) relay closes to cranks the starter, and K3 (ignition) relay closes to energize the

ignition. The K2 relay remains closed until either the generator starts or the maximum cranking time period (0 to 60

seconds) is reached.

4. If the generator fails to start after cranking, K1, K2 and K3 relays open for a resting period equal to twice the maximum

cranking time adjustment, the maximum crank LED blinks during this period. Halfway through the resting period K4

(shutdown) relay energizes for 7 seconds to ensure the generator did not start before beginning the cranking sequence

routine again. If the generator starts and shuts down after each starting attempt , operator needs to check the AC

feedback signal to make sure it is present when the generator starts and is running.

5. If the generator fails to start after 4 cranking attempts, K1, K2 and K3 relays open, K4 (shutdown) relay closes for 5

seconds and then opens to ensure the generator is not running, then the maximum crank shutdown LED lights and the

GSCM enters the maximum crank lockout condition. This lockout condition remains until the GSCM is reset by

momentarily shorting the reset terminals 7 and 8 together, after which the start LED blinks for 60 seconds and then enters

ready mode. Powering down the GSCM for 5 seconds and powering it back up will also clear the maximum crank lockout

condition, with the GSCM returning to ready mode.

6. When the generator starts, K2 (crank) relay immediately opens, stopping the cranking, K1 (glow plug) relay remains

energized for an additional 5 seconds and then opens, de-energizing the glow plugs or removing a low oil pressure lockout

during the starting routine. The K3 (ignition) relay remains closed during the run operation. A valid run condition is

determined by the generator's AC output frequency exceeding the 30Hz run/crank disconnect setting (adjustable

between 15 and 75Hz).

7. If the generator starts but shuts down after a few seconds due to a fuel problem, etc., the start sequence will revert to

ready mode after a 60 second delay period in which the start LED blinks rapidly. The GSCM will then try to start the

generator again in manual mode or after a 5 minute delay period in auto-stat mode. When the run condition is detected,

the GSCM enters a load transfer delay period, before energizing the K5 (load) relay, the load delay LED blinks during the

delay.

8. After the load transfer delay period, K5 (load) relay energizes to transfer the electrical load to the generator.

9. The generator continues to run until one of the following occurs: the manual start signal is no longer received, the auto

battery charge voltage is reached, the 30 day exercise cycle time out or either an oil pressure or high temperature fault

condition occurs.

10. During normal shutdown, K5 (load) relay opens and the GSCM enters the pre-off (cool down) time period, indicated by

the load pre-off LED blinking.

11. When the pre-off period expires, K3 (ignition) relay opens, ½ second later the K4 (shutdown) closes, to shut down the

generator by grounding the ignition, etc. It remains closed for 5 seconds after the AC Hz signal from the generator goes to

zero, ensuring the generator has shutdown.

12. If the manual start signal is removed or switch is turned off before K5 (load) relay energizes, K3 (ignition) relay opens, then

K4 (shutdown) relay energized shutting down the generator. The GSCM then enters a 60 second delay period before

returning to ready mode.

13. If the load pre-off time delay is set to 0V, then the K5 (load) and K3 (ignition) relays de-energize simultaneously for

shutdown followed by K4 (shutdown) relay energizing to ensure the generator shuts down.

14. The generator remains off until another start signal is received.

www.atkinsonelectronics.com

800.261.3602

Circuit Board Division

Revised 09/18