Bose SoundTouch Panduan Servis - Halaman 34

Jelajahi secara online atau unduh pdf Panduan Servis untuk Pembicara Bose SoundTouch. Bose SoundTouch 39 halaman. Wireless pedestal
Juga untuk Bose SoundTouch: Panduan Pemilik (33 halaman), Panduan Pemilik (32 halaman), Panduan Memulai Cepat (2 halaman), Manual (9 halaman), Panduan Pemilik (20 halaman), Panduan Pemilik (32 halaman), Panduan Memulai Cepat (5 halaman), Mulai dari Sini Manual (20 halaman), Panduan Memulai Cepat (2 halaman), Panduan Pemilik (18 halaman), Panduan Memulai Cepat (5 halaman), Panduan Memulai Cepat (2 halaman)

Halaman Cetak

2.2 The song "Take 5" should play. Listen for

clean undistorted audio.

2.3 Enter the following TAP command to exit

the Wi-Fi test.

demo exit <enter>

Note: A Tera-Term macro that includes these

TAP commands is available for download on

the product's repair information page. Place

the macro file in the same folder as your

Tera-Term program. Open Tera-Term, select

Control, Macro, wifi_test.ttl. Once the macro

runs, follow the prompts.

3. Factory Default Unit

3.1 Enter the TAP command

sys factorydefault <enter>

3.2 Provide the customer instructions for

reconnecting their system to their Wi-Fi

network. Download the instructional sheet on

the product's repair information page.

4. USB Port Functional Test

4.1 Connect the SoundTouch wireless

pedestal to a computer as shown in the TAP

command set up documented on pages 31 -

32.

4.2 Type the command "local_services on"

and <enter>. Then press CTRL-C on the

keyboard. Then type "e" and <enter>. The

command line lisa login: should be displayed

on the computer.

4.3 Type the command "root" and <enter>.

The command line should be

root@lisa:root#.

4.4 Connect a USB thumb drive to the USB

port located on the back of the product.

4.5 Type the command "lsusb".

TEST PROCEDURES

5. Micro USB Port Functional Test

6. Ethernet Connector Functional Test

4.6 Verify the unit responds with the name of

the USB thumbdrive. Sample response -

Bus 002 Device 002: ID 0781:5151 SanDisk

Corp. Cruzer Micro Flash Drive.

4.7 Send the command "rm /mnt/nv/

local_services" and <enter>.

4.8 Send the command "exit" and <enter>.

This will return to the TAP interface (CLI) and

a TAP command line "->" should be shown.

5.1 Using a micro USB to standard USB

cable, insert the micro USB end of the cable

into the SoundTouch connector labeled

SETUP A (micro USB). Plug the other end of

the cable into a USB port on a computer.

Ensure that cable is properly seated.

5.2 Open your device manger and look

under Network Adapters. You should see the

SoundTouch Wi-Fi adapter as an adapter.

Directions: On your computer, click on

Start and navigate to Run. In the window

that opens, enter "mmc devmgmt.msc".

The device manager will open. In the device

manager, expand the network adapters, you

should see the SoundTouch wireless pedes-

tal as an adapter.

6.1 Insert an Ethernet cable into the Ethernet

connector on the SoundTouch system.

Connect the other end of the cable to the

router.

6.2 The LED lights on the product's Ethernet

connector should light up yellow and green

after a few seconds indicating that the

connector is functioning.