3M XT-1 Manual - Halaman 7

Jelajahi secara online atau unduh pdf Manual untuk Headset 3M XT-1. 3M XT-1 8 halaman. Drive-thru systems
Juga untuk 3M XT-1: Panduan Referensi Cepat (6 halaman), Panduan Referensi Cepat (2 halaman), Buletin Teknis (10 halaman), Data Teknis (2 halaman), Buletin Teknis (2 halaman), Panduan Memulai Cepat (3 halaman)

3M XT-1 Manual
Registering Headsets (G5 or XT-1)
Each headset must be registered to a base station before it can be used. Once registered, it should not need
to be registered again unless it is intentionally removed.
Add Headsets (G5 and/or XT-1)
Each headset has a unique identification number. The number is imprinted on the headset and broadcast to
the base station whenever it is turned on.
Note: A single headset should not be registered to more than one base station at any given site, whether or not the
bases are interconnected. Remove the headset from the existing base station before adding it to a different one. In
dual-lane installations, all headsets are registered to Base #1.
To register a headset:
1. Enter the base station configuration mode.
2. Select 04 Registration > 1 Add New Headsets.
3. Power on the headset when prompted. Or in the case of a G5 headset, insert he battery to automatically
power on the headset.
4. Wait up to two minutes for {Headset xxxxxxx Has Been Registered!} to appear at the bottom
of the display.
5. Repeat step 3 for additional headsets.
6. Press Mode when finished.
Remove Headsets
Perform the following steps to un-register a lost, destroyed, or otherwise removed headset from the system,
including a headset that is sent back to 3M for repair. The repaired headset would have to be registered again
at a later date.
1. Enter the base station configuration mode.
2. Select 04 Registration > 2 Remove Headsets.
3. Scroll to the number of the headset you want to un-register.
4. Press Enter.
Note: If you do not know or have access to the number of the headset to be unregistered, identify the headsets that
you want to remain in service and un-register any that remain on the list.
List All Headsets
To see a list of the registered headsets:
1. Enter the base station configuration mode.
2. Select 04 Registration > 3 List All Headsets.

Change Site Scheduling

The site schedule is the calendar of store open and closing times.
Note: All timekeeping is done using a 24 hour clock (e.g., 6:00 p.m. appears as 18:00).
Regular Site Schedule:
The regular site schedule is the opening and closing times for each day of the week and the times assigned
as "Day" and "Night," which determine when the day and night volume settings change. Perform the
following procedure to set the regular site schedule:
1. Enter the base station configuration mode.
2. Navigate to 10 Site Scheduling > Regular Site Schedule.
3. Change the value for each day of the week and each of the four defined fields
(Open, Day, Night, and Close). Press s, t , and to scroll up and down the list.
Holiday/Exception Schedule:
The holiday/exception schedule can be used to identify up to 12 days in the year on which the store schedule
is different than it would have been otherwise. The holiday/exception schedule should be updated at least
once a year to ensure it conforms to the current year's calendar. Perform the following procedure to set the
holiday/exception schedule:
1. Enter the base station configuration mode.
2. Navigate to 10 Site Scheduling > Holiday/Exception Schedule.
3. For each day that needs a non-typical schedule, enter the three-letter month and two digit date under
Date, then change the open and close times on the line to the right of the date. Press s, t , and to
scroll through the fields.
7