DSC Maxsys PC4116 Petunjuk Instalasi

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Unit Kontrol DSC Maxsys PC4116. DSC Maxsys PC4116 2 halaman. Zone input module

Halaman Cetak

Introduction

The PC4116 is a zone input module that adds up to 16

fully programmable zones to the Maxsys security system.

Specifications

• Connects to control panel via 4-wire Combus

• Current Draw: 30 mA(from Combus)

• Supports no end-of-line, single end-of-line and

double end-of-line zone loops (5600 ohm resistors)

• AUX+ output: 12V

Combus)

• Tamper contact input

Compatible Cabinets

• PC4051C/CR*

• PC4001C

• PC4054C

*CR cabinet for North American customers only

Installing the PC4116

3.1 Unpacking

The PC4116 package includes the following parts:

• One PC4116 circuit board

• 32 end-of-line resistors (5600 ohms)

• Five plastic stand-offs

3.2 Mounting

The PC4116 should be located inside a compatible cabinet,

mounted in a dry, secure location. Preferably, it should be

placed at a convenient distance from the connected devices.

Perform the following steps to mount the unit:

1. Press the five plastic stand-offs through the mounting

holes at back of the cabinet.

2. Secure the cabinet to the wall in the desired location.

Use appropriate wall anchors when securing the

cabinet to drywall, plaster, concrete, brick or other

surfaces.

3. Press the circuit board into the five plastic stand-offs

to secure the unit to the cabinet.

Once the unit is mounted, wiring may be completed.

3.3 Installation and Wiring

Before beginning to wire the unit, ensure that all power

(AC transformer and battery) is disconnected from the

control panel.

Perform the following steps to complete wiring:

1. Connect the four Combus wires to the PC4116.

Connect the red, black, yellow and green Combus

wires to the RED, BLK, YEL and GRN terminals,

respectively.

2. Complete all zone wiring to the zone input terminals

(Z1-Z16). See the control panel Installation Manual

for details on zone wiring configurations.

Please refer to the System Installation Manual for information on limitations regarding product

use and function and information on the limitations as to liability of the manufacturer.

, 250mA max. (drawn from

PC4116 Zone Input Module

3. Connect the external tamper switch, if used.

Consult the wiring diagram above for further information.

3.4 Applying Power

After all wiring is completed, apply power to the control

panel. Connect the battery leads to the battery, then connect

the AC transformer. For more information on control panel

power specifications, see the control panel Installation

Manual.

NOTE: Do not connect the power until all wiring is

complete.

Enrolling the Module

Once all wiring is complete, the module must be enrolled

on the system. To enroll the module, perform the

following:

1. Enter installer's programming by pressing [*] [8]

[Installer's Code].

2. Scroll to "Module Hardware" and press the [*] key.

3. Scroll to "Enroll Module" and press the [*] key.

4. Scroll through the different modules until "PC41XX"

is displayed. Press the [*] key.

5. The message "Create Tamper on Desired Unit" will

be displayed. To create the required tamper, secure

the tamper zone on the module and then open it. The

transition from secure to violated enrolls the module.

After this is done, the keypad will display the module

number and will confirm enrollment (e.g. "PC4116

Mod 01 Enrolled").

Zones 1-8 (PC4010)/1-16 (PC4020) are located on the main

control panel. Additional zones are added in sequence. For

example, if two PC4116 zone expanders are enrolled, the

first one enrolled will be assigned zones 17 to 32 and the

second will be assigned zones 33 to 48. To confirm which

zones are assigned to which expander, press the arrow key

when the enrollment confirmation message is displayed.

For more information regarding module enrollment, see

the control panel Installation Manual.

Programming the Module

To access PC4010/4020 programming, enter [*][8] followed

by the Installer's code. The zones connected to the module

must be added to a partition and programmed for

operation. The programming worksheet located on this

sheet indicates which sections must be programmed.

For more information regarding zone programming, see

the control panel Installation Manual.

NOTE: The zone types and attributes listed below are for

PC4010/4020 v3.0. For zone programming for previous

software versions, see the corresponding programming

manual.

Installation Instructions