DSC Misterhouse PC5401 Petunjuk Instalasi - Halaman 2
Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Unit Kontrol DSC Misterhouse PC5401. DSC Misterhouse PC5401 2 halaman. Data interface module
Halaman CetakTable 1: BAUD Selection
BAUD selection can only be changed by cycling power to the module.
BAUD
4800
19200
57600
9600
Table 2: Indicator LEDs
LED
Description
KEYBUS Link
KEY
Active
Module Status
PWR
Limited Warranty
Digital Security Controls warrants that for a period of twelve months from the date of purchase, the product shall be free of defects in
material and workmanship under normal use and that in fulfillment of any breach of such warranty, Digital Security Controls shall, at its
option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in
parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond control of Digital Security
Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper
application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other
warranties, whether express or implied and of all other obligations or liabilities on the part of Digital Security Controls . This warranty
contains the entire warranty. Digital Security Controls neither assumes responsibility, nor authorizes any other person purporting to act on
its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall
Digital Security Controls be liable for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other
losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.
WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due
to but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer's instructions, may cause
interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in
Subpart "B" of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Re-orient the receiving antenna
•
Relocate the alarm control with respect to the receiver
•
Move the alarm control away from the receiver
•
Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet
prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing
Office, Washington D.C. 20402, Stock # 004-000-00345-4.
© 2004 Digital Security Controls
Toronto, Canada • www.dsc.com
Technical Support: 1-800-387-3630
Printed in Canada
JMP3
ON
ON
ON
OFF
Normal
Operation
GREEN
Solid
RED
Flashing
(2 seconds)
JMP2
ON
OFF
OFF
OFF
Indicates the module is correctly connected to
the KEYBUS
LED Flashes every 2 seconds when module is
operating normally. A solid RED means that
the module is not operating properly. If the
LED is unlit, the module is not powered
correctly, check cabling.
JMP1
OFF
ON
OFF
OFF
Notes
29007103R001