DSC Misterhouse PC5401 설치 지침 - 페이지 2

{카테고리_이름} DSC Misterhouse PC5401에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC Misterhouse PC5401 2 페이지. Data interface module

페이지 인쇄

Table 1: BAUD Selection

BAUD selection can only be changed by cycling power to the module.

BAUD

4800

19200

57600

9600

Table 2: Indicator LEDs

LED

Description

KEYBUS Link

KEY

Active

Module Status

PWR

Limited Warranty

Digital Security Controls warrants that for a period of twelve months from the date of purchase, the product shall be free of defects in

material and workmanship under normal use and that in fulfillment of any breach of such warranty, Digital Security Controls shall, at its

option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in

parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond control of Digital Security

Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper

application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other

warranties, whether express or implied and of all other obligations or liabilities on the part of Digital Security Controls . This warranty

contains the entire warranty. Digital Security Controls neither assumes responsibility, nor authorizes any other person purporting to act on

its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall

Digital Security Controls be liable for any direct, indirect or consequential damages, loss of anticipated profits, loss of time or any other

losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.

WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due

to but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer's instructions, may cause

interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in

Subpart "B" of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Re-orient the receiving antenna

•

Relocate the alarm control with respect to the receiver

•

Move the alarm control away from the receiver

•

Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet

prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing

Office, Washington D.C. 20402, Stock # 004-000-00345-4.

Toronto, Canada • www.dsc.com

Technical Support: 1-800-387-3630

Printed in Canada

JMP3

OFF

Normal

Operation

GREEN

Solid

RED

Flashing

(2 seconds)

JMP2

OFF

Indicates the module is correctly connected to

the KEYBUS

LED Flashes every 2 seconds when module is

operating normally. A solid RED means that

the module is not operating properly. If the

LED is unlit, the module is not powered

correctly, check cabling.

JMP1

OFF

Notes

29007103R001