3Ware 3WARE 9650SE Spesifikasi - Halaman 6

Jelajahi secara online atau unduh pdf Spesifikasi untuk Multiplexer 3Ware 3WARE 9650SE. 3Ware 3WARE 9650SE 7 halaman. Remote battery board
Juga untuk 3Ware 3WARE 9650SE: Adendum Panduan Pengguna (1 halaman), Panduan Pengguna (11 halaman), Panduan Instalasi (4 halaman)

Halaman Cetak
Using the AMCC 3ware® I2C Multiplexer with a Supermicro® Backplane
Appendix: Jumper and Cable Pin Settings
Note
:
The following jumper setting information is provided as a reference for your convenience. For complete and current information about the
2
I
C
appropriate
settings for your backplane, be sure to consult the documentation from Supermicro.
Jumper Settings for Supermicro 826TQ
Table 1: Reset Chip Settings
These jumpers control the AMI 9072 and AMI 9071 chips
Jumper Jumper Settings
JP35
Open: No Reset (Default)
Closed: Reset
JP50
Open: No Reset (Default)
Closed: Reset
2
Table 2: I
C Setting (Default)
These jumpers control the I2C and SGPIO settings for the 826TQ
Jumper
JumperSetting
JP65
2-3
JP67
2-3
JP 74
2-3
JP83
Closed
JP84
2-3
JP85
1-2:ID#0
JP86
Closed
JP87
Open
JP88
Open
JP89
Closed
JP90
2-3
JP91
1-2:ID#0
JP93
Open
JP101
2-3
JP102
2-3:ID#1
6
Note
This is a 2-pin jumper block.
Jumper should be removed.
This is a 2-pin jumper block.
Jumper should be removed.
Note
Backplane ID SDIN #1
Backplane ID SDIN #2
Backplane ID SDIN #3
I2C Reset #1
Controller ID #1
Backplane ID #1
I2C Reset #2
Reset SDOUT #1
Reset SDOUT #2
Reset #3
Controller ID #3
Backplane ID #3
Reset SDOUT #3
Controller ID #2
Backplane ID #2
Jumper Settings for Supermicro 836TQ
Table 3: Reset Chip Settings
These jumpers control the AMI 9072 chip
Jumper Jumper Settings
JP35
Open: No Reset (Default)
Closed: Reset
JP50
Open: No Reset (Default)
Closed: Reset
Table 4: I2C Setting (Default)
These jumpers control the I2C and SGPIO settings for the 836TQ
Jumper
Jumper Settings
JP65
2-3
JP67
2-3
JP 74
2-3
JP83
Closed
JP84
2-3
JP85
1-2:ID#0
JP86
Closed
JP87
Open
JP88
Open
JP89
Closed
JP90
2-3
JP91
1-2:ID#0
JP93
Open
JP101
2-3
JP102
2-3:ID#1
JP103
2-3
JP104
2-3:ID #1
AMCC 3ware I
Note
This is a 2-pin jumper block.
Jumper should be removed.
This is a 2-pin jumper block.
Jumper should be removed.
Note
Backplane ID SDIN #1
Backplane ID SDIN #2
Backplane ID SDIN #3
I2C Reset #1
Controller ID #1
Backplane ID #1
I2C Reset #2
Reset SDOUT #1
Reset SDOUT #2
Reset #3
Controller ID #3
Backplane ID #3
Reset SDOUT #3
Controller ID #2
Backplane ID #2
Controller ID #4
Backplane ID #4
2
C MUX Documentation