aevit 2.0 Panduan Instalasi - Halaman 12

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Dudukan TV aevit 2.0. aevit 2.0 17 halaman. Mounting brackets

Halaman Cetak

prIMArY INpUT

2.5 OThEr MOUNTINg OpTIONS

(CONTINUEd)

ATTAChINg ONLY ThE INpUT dEVICE SwIVEL BrACkET (CONTINUEd)

sTEP 1

Remove the Input Device Articulating Swivel

Bracket from the quick Adjust Upper Pole. (See

Figure 8, Page 2-5 for information on this assem-

bly). Also, remove the Input Device Swivel Bracket,

(1) 2" Dia rubber washer, and Adjustment Knob

1 (Figure 9, Page 2-5). These components will be

used in step 5 of this section.

sTEP 2

At this point, there will be a threaded rod protrud-

ing from the quick Adjust Upper Pole. Insert the

3/8" Flat Washer and Adjustment Knob 1 onto the

Threaded rod (Figure 23a). This hardware will be

used to lock the quick Adjust Upper Pole in place

much like step 2 Page 2-5. Tighten the adjustment

knob and make a mark on the threaded rod such

that it can be cut as to not protrude from the top

of the adjustment knob when the installation

is completed (Figure 23b). This can be done by

simply making a mark on the rod at the top of

Adjustment Knob 1 and then removing the knob

and washer and cutting the threaded rod approxi-

mately 1/4" beneath the mark. (Figure 24a).

hINT:

PRIOR TO CUTTING ThE ThREADED ROD, ThREAD

(1) 3/8" NUT (NOT INCLUDED) ONTO ThE ThREAD-

ED ROD, ThEN MAKE ThE CUT. AFTER ThE ROD IS

CUT, REMOVE ThE 3/8" NUT FROM ThE CUT END OF

ThE ROD TO CLEAN/DEBUR ThE ThREADS.

Figure 24b shows what this assembly should look

like after cutting the threaded rod.

sTEP 3

Reinstall Adjustment Knob 1 and (1) 3/8" flat

washer as shown in Figure 23a

sTEP 4

Once the quick Adjust Upper Pole is in position, a

3/8" thru hole will need to be drilled into it. Notice

in Figure 25, there is a support webbing under-

neath the quick Adjust Upper Pole. The 3/8" thru

hole can be drilled anywhere along either of the

two (2) dotted lines shown in Figure 26. Basically,

the 3/8" hole will need to be drilled 7/8" from ei-

ther side of the quick Adjust Upper Pole such that

the nylon and flat washers of the Input Device

Swivel Bracket will not interfere with the support

webbing underneath.

(BrkT-AEVIT-FLr & BrkT-AEVIT dOOr)

ADjusTMENT

kNOb 1

3/8" FlAT

QuIck ADjusT

wASHER

uPPER POlE

THREADED

ROD

FIGuRE 23a

Make cut

here

cuT MARk

3/8" NuT

(see hint)

FIGuRE 24a

suPPORT

wEBBINg

FIGuRE 25 - QuIck ADjusT uP-

PER POlE: uNDERsIDE

AEVIT 2.0 MOUNTING BRACKETS INSTALL MANUAL

Make cut Mark flush with the

top of the adjustMent knoB

cuT MARk

FIGuRE 23b

FIGuRE 24b

3/8" hOlE cAN bE DRIllED

ALONg EITHER DOTTED

LINE SHOwN

7/8"

FIGuRE 26 - QuIck ADjusT uP-

PER POlE: TOPsIDE

2-9