Austral Lock YR4000 Ilustrasi Petunjuk Pemasangan

Jelajahi secara online atau unduh pdf Ilustrasi Petunjuk Pemasangan untuk Dengan kunci Austral Lock YR4000. Austral Lock YR4000 2 halaman.

Halaman Cetak

YARRA RIDGE

Illustrated Fitting Instructions

These instructions describe the steps to install a standard Yarra Ridge lock

for general application. For other Yarra Ridge variations and non-standard

applications, additional instructions may be required.

Read through all instruction steps before beginning installation. When

replacing an older lock, modify the existing installation holes in the door stile

and jamb if necessary.

IMPORTANT: If installing an EGRESS Yarra Ridge D-Pull, test the lock

after installation to ensure correct operation.

The interior lever on the EGRESS D-Pull must allow unlocking at all times.

Test by locking the exterior by key, then rotate the interior lever.

The interior lever must be free to retract the beaks.

Step 1

For optimal installation, ensure the door is rolling smoothly and closing

parallel into the jamb by lubricating and adjusting the rollers. Close the

door and lightly mark the door stile at the edge of the overlapping jamb.

Prepare three 9.0mm holes in the door stile as dimensioned below in

Figure A. Ensure the holes are straight and free from burr.

Door Stile

Door Jamb

Mark and measure

from this edge

Mark

9.0 mm

Door Stile

Step 2 (optional)

To remove a Cylinder Plug and install a Keyed Cylinder in the Exterior

Assembly, remove the Base Plate Screw and lift off the Base Plate Assembly.

Remove and discard the Cylinder Plug.

Install the Keyed Cylinder into the Exterior Pull by matching the orientation

shown in Figures B and C.

Hold the Base Plate Assembly by the Spindle. Using the Alignment Markings

on the Base Plate as a guide, ensure the Cylinder Gear is orientated as

shown in Figure D.

Place the Base Plate Assembly onto the Exterior Pull. If the Base Plate does

not sit flush with the rear of the Exterior Pull, rotate the Spindle until it drops

into place. Replace the Base Plate Screw.

Spindle

Base Plate

Assembly

Keyed Cylinder

Exterior

Spigot

Interior

Figure B

Exterior Pull Assembly

14.0 mm

Figure C

Installing a

Keyed Cylinder

41.0 mm

Cylinder Gear

41.0 mm

Figure D

Cylinder Gear Orientation

Figure A

Base Plate

Screw

Cylinder Plug

Exterior Pull

Base Plate

Alignment

Markings

PLEASE TURN PAGE FOR INSTALLATION STEPS 5 - 8

Step 3

Use the table below with Figure E to decide the correct length of the

Spindle. Add 8mm to thickness in table if using packers. If necessary,

use pliers or a vice to carefully break off the required number of

pre-notched portions of the Spindle to suit the door thickness.

Door thickness

Spindle preparation

46.4 to 40.2mm

Break off '0' portions

40.1 to 33.9mm

Break off '1' portion

33.8 to 27.6mm

Break off '2' portions

27.5 to 21.3mm

Break off '3' portions

Discard

Notch

Spindle

Figure E

Step 4

Several pairs of Fixing Screws are provided to suit different door

thicknesses. Use the table below to identify which are the correct

length Fixing Screws. Add 8mm to thickness in table if using packers.

Door thickness

Screw selection

46.4 to 40.2mm

1 ¾" Fixing Screw

40.1 to 33.9mm

1 ½" Fixing Screw

33.8 to 27.6mm

" Fixing Screw

27.5 to 21.3mm

1" Fixing Screw

Figure F

(PK0233) YR4000 Instructions (Trade A4) R5.cdr