AutomationDirect DURApulse GS20 Panduan Memulai Cepat - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Penggerak DC AutomationDirect DURApulse GS20. AutomationDirect DURApulse GS20 8 halaman.

Halaman Cetak
DURApulse GS20 AC Drive Quick-Start Guide

Environment for Operation, Storage, and Transportation

DO NOT expose the GS20 drive to environments that contain dust, direct sunlight, corrosive/inflammable
gases, high humidity, liquids, or high vibration. The salt in the air must be less than 0.01 mg/cm
the year.
Installation Location
IEC60364-1/IEC60664-1 Pollution degree 2, Indoor use only
Storage: -40°C to +85°C
Transportation: -20°C to +70°C
Surrounding
Temperature
No condensation, non-frozen
Operation: Max. 90%
Storage/Transportation: Max. 95%
Rated Humidity
No condensed water
Air Pressure
Operation/Storage: 86 to 106 kPa
Transportation: 70 to 106 kPa
IEC60721-3
Operation:
Storage:
Pollution Level
Class 3C2; Class 3S2
Class 2C2; Class 2S2
No concentrate
If the GS20 drive is installed at altitudes of 0~1000m, follow normal
operation restriction. If installed at altitudes of 1000~2000m, decrease
1% of rated current or lower 0.5°C of temperature for every 100m
Altitude
Operation
increase in altitude. Maximum altitude for Corner Grounded is 2000m.
Contact ADC for more information if you need to use this motor drive at
an altitude of 2000m or higher.
Storage
Package
ISTA procedure 1A (according to weight) IEC60068-2-31
Transportation
Drop
1.0mm, peak-to-peak value range from 2Hz to 13.2 Hz; 0.7G~1.0G range from
Operating
13.2Hz to 55Hz; 2.0G range from 55Hz to 512 Hz. Comply with IEC 60068-2-6.
Vibration
Non-operating
2.5 G peak, 5Hz~2kHz: 0.015" maximum displacement.
Operating
IEC/EN60068-2-27: 15G, 11ms
Impact
Non-operating
30G
IP40 - main unit
IP20 - wiring area (main circuit terminals and control terminals (all frame types),
Protection Level
and the vent near the capacitor on frame C, D, E, and F types).
To prevent personal injury, please make sure that the case and wiring are installed
according to these instructions. The figures in these instructions are only for reference.
They may be slightly different from the one you have, but it will not affect your
customer rights.
These installation instructions may be revised without prior notice. The most recent
edition can be downloaded from the AutomationDirect web site at any time:
http://www.automationdirect.com/static/manuals/index.html.

Minimum Mounting Clearances

When installing your GS20 drive, please keep the following in mind:
• Prevent fiber particles, scraps of paper, shredded wood, saw dust, metal particles, etc., from adhering to the
heat sink.
• Install the AC motor drive in a metal cabinet. When installing one drive below another one, use a metal
separation between the AC motor drives to prevent mutual heating and to prevent the risk of accidental fire.
• Install the AC motor drive in Pollution Degree 2 environments only: normally only nonconductive pollution
occurs and temporary conductivity caused by condensation is expected.
←
(Blue Arrow) Inflow
←
(Red Arrow) Outflow
Single drive Independent installation.
Side-by-side horizontal installation:
A
B
C
Installation Method
(mm)
(mm)
(mm)
–
Single drive installation
50
30
Side-by-side horizontal installation
50
30
30
Zero stack installation
50
30
0
GS20_QSP 1st Edition, Rev C 03/03/2022
2
throughout
Transportation:
Class 1C2; Class 1S2
Operation Temperature
Max
Max
(w/out derating)
(Derating)
50
60
50
60
40
50
DURApulse GS20 AC Drive Quick-Start Guide – 1st Ed, Rev C 03/03/2022
Page 6