Dynamic CCTV DVR-8 Panduan Pengguna - Halaman 12

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk DVR Dynamic CCTV DVR-8. Dynamic CCTV DVR-8 18 halaman. 8 channel digital video multiplex recorder

Halaman Cetak

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

2-7. HDD connection

MAIN BOARD

Connect main board and HDD using IDE HDD cable and power cable

included in the package. If you install a unit of HDD, jumper setting

of HDD must be on (DS) Master, as specified by HDD manufacturer.

Fix HDD on the bottom of DVMR case using screws included in the

package. Screws must be inserted from outside of the bottom.

And CD-RW drive must be on Slave.

CD-RW

Notice : Formatting before installation is not required, because

HDD1

DRIVE

DVMR system automatically detects and formats HDD.

(MASTER)

(SLAVER)

In the first operation after installation of HDD, first set at

FACTORY DEFAULT in setup menu of DVMR system and then

do HDD CLEAR in HDD MANAGEMENT in setup menu of

DVMR system.

Notice : In case you see "UNKNOWN HDD DETECTED" message is displayed after booting process, just clear

HDD and set at FACTORY DEFAULT to make this HDD be detected by DVMR system.

2-8. Power Connection

Connect the power to the POWER CONNECTION on the Rear Panel of the system,

and turn on the switch.

DC 12V

Notice : To turn off DC power switch on the front panel of DVMR case, be sure to press [MENU] button first.

If you press [MENU] button, DVMR system stops recording, and you can cut power to DVMR unit

while HDD head is not in writing mode. It is necessary to press [MENU] button first and turn DC power

switch off for protection of HDD head from being damaged and eliminate possibility of mal-function of DVMR unit.

Turn on the POWER and Log-in to the system

Follow instruction in the Log-in part of this manual to input the PASSWORD and start the system.

Factory default password for account manager and user, set by manufacturer, is null, therefore

just press [ENTER] button in case DVMR system asks to input password, as far as you did

not change password.

Detail setup in SYSTEM SETUP

For detail setup, refer to the instruction of SYSTEM SETUP.

2. Installation

8 channel stand-alone DVMR

2) ALARM SETUP

In DVMR system, 8 alarm input, one for each channel,

and 1 alarm output(relay out) is provided, and we can set

type of alarm sensor independently in ALARM SETUP.

Or you can set all of input alarm sensors at "NO", "NC" or

DISABLE by setting ALL at "NO", "NC" or DISABLE, by

pressing [ENTER] button or [LEFT] or [RIGHT] button.

In the same way, we can set type of relay out at "NO",

"NC" or DISABLE, by pressing [ENTER] button or [LEFT]

or [RIGHT] button.

To save settings and exit, press [MENU] button.

3) TIMER SETUP

In DVMR system, we have 3 kind of timer settings as

follows.

FULL SCREEN timer :

Rotating cycle time of full screen in live mode, when

[SEQ] button is pressed for long time.

QUAD SCREEN timer :

Rotating cycle time of quad(4-split) screen in live mode,

when [SEQ] button is pressed for long time.

PIP SCREEN timer :

Rotating cycle time of PIP screen in live mode, when

[PIP] button is pressed in live mode.

If you press [SEQ] button for long time, full screen picture

also rotates with time interval of FULL SCREEN timer, in

addition to PIP.

To save settings and exit, press [MENU] button.

4) PAN/TILT CMD SETUP

Just with operation buttons on the front panel of DVMR

unit, we can control PTZ camera connected to DVMR unit

via RS-485 port, if protocol of PTZ camera connected to

DVMR unit is same as one of built-in protocols, just select

model among models in PAN/TILT CMD SETUP.

In case PTZ camera you connected to DVMR unit is not a

model whose protocol in incorporated into DVMR unit,

you are requested to select USER DEFINE and input

protocol by yourself.

To save settings and exit, press [MENU] button.

3. Operation

ALL ABOUT IMAGE RECOGNITION & PROCESSING

ALARM SETUP

ALL : --

CH 01 : NO

CH 02 : NO

CH 03 : NO

CH 04 : NO

CH 05 : NO

CH 06 : NO

CH 07 : NO

CH 08 : NO

RELAY : ENABLE

NO . . . . . NORMAL OPEN

NO . . . . . NORMAL CLOSE

- - . . . . . DISABLE

SELECT

, EDIT ENTER /

ALARM SETUP

TIMER SETUP

FULL SCREEN

1 SEC

QUAD SCREEN

3 SEC

PIP SCREEN

2 SEC

SELECT

, EDIT ENTER /

TIMER SETUP

PAN/TILE CMD SETUP

MODEL : PELCO D TYPE

P-SPD : 80

T-SPD : 80

Z-SPD : 80

F-SPD : 80

DEV : 1 ST

CMD : POWER ON

LEN : 07 BYTE

DELAY : 15

NO HEXA

---- -------

06 -- 00

11 -- 00

01 -- FF

02 -- 01

07 -- 89

12 -- 00

03 -- 88

08 -- 00

13 -- 00

04 -- 00

09 -- 00

14 -- 00

05 -- 00

10 -- 00

15 -- 00

COPY : REC

PASTE : PLAY

SELECT

, EDIT NUMERIC /

PAN/TILT CMD SETUP